800628

Innoliving INN-680 Manual

20
Zoom out
Zoom in
Previous page
1/24
Next page
20
FIRST USE
I FILLING WITH WATER
ATTENTION! Before lling the boiler, switch off the appliance and remove the plug from the socket.
• Fill the boiler exclusively with water, possibly distilled, or with tap water with a low mineral
content. The formation of limescale in the appliance can cause the machine to overheat and
clog the steam outlet ducts.
• The ironing system must rest on a at surface.
• Turn the cap (4) anticlockwise until it is completely unscrewed.
• Empty the boiler of any residual water. Pour the water only when the boiler is empty.
• Place a funnel over the lling opening.
• Pour in an adequate quantity of water (with empty tank min 0.2 l. - max 0.5 l.).
ATTENTION: Do not pour more than 500 cc (0.5 l) of water. Never exceed this amount!
• Remove the funnel.
• Replace the cap by turning it clockwise until it is screwed in completely.
ATTENTION: Make sure that the cap is screwed on well and the tank is therefore tightly closed.
CONNECTING THE IRONING SYSTEM - ATTENTION!
• Only connect the appliance if the mains voltage corresponds to the rated voltage shown on
the technical data plate.
• The power cable and the pipe connecting the iron to the boiler must not be visibly damaged.
• The water tank must be lled with enough water (min 0.2l. - max 0.5l.)
• Do not in any way impede the release of steam from the iron soleplate.
• At this point, press the boiler heating switch (1); the switch lights up (this operation is not
necessary if you want to iron dry).
• The ironing system is on and in operation; the water heats up and steam is created.
• When the ironing system is ready, the light (3) is on; wait for the iron to be ready for use
before dispensing steam (see next paragraph).
• It is normal for the lights to go on and off during operation. This indicates that the
thermostats that control the temperature are working properly.
TURNING ON THE IRON
• After connecting the ironing system to the mains, you can switch on the iron by pressing the
switch (2) located on the ironing system. The switch (2) and the light on the iron will light
up to indicate that the iron is on.
• Adjust the knob of the iron according to the fabric.
• The iron is ready for use when the light on the iron (5) is off and when the light (3) on the
body of the boiler is on. When both the iron and the boiler are ready for use, you can press
the button on the iron to dispense steam. To have a continuous jet, you can lock the steam
button on the iron with the appropriate lever.
POUR MORE WATER INTO THE BOILER
ATTENTION! Do not open the boiler cap during operation and before the boiler has cooled
down properly!
To rell the tank, proceed as follows:
• Turn off the boiler (1) and iron (2) switches.
• Pull the plug out of the socket and let the machine cool down for at least 5 minutes.
• Slowly turn the cap 2-3 turns anticlockwise, allowing the residual steam in the boiler to
GB
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Innoliving INN-680 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Innoliving INN-680 in the language / languages: English, Italian as an attachment in your email.

The manual is 1.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info