647427

Ilve M-120 Manual

47
Zoom out
Zoom in
Previous page
1/66
Next page
Pressure Adjustment
First turn the gas off to the appliance. Remove the sealing screw from the regulator’s test point at the
rear of the appliance and place the hose of the Manometer onto it. Turn the gas on to the appliance and
light the Wok Burner and Small Burner at maximum setting. Check the pressure and adjust at the regulator
if necessary to the setting in the table on the last page or the Data plate. For ULPG Gas adjust at the
regulator on the cylinder – Turn regulator adjusting screw clockwise increases pressure whilst
anti-clockwise decreases pressure. Refit the test point sealing screw when finished.
Electrical Equipment and Components
Electrical componentry is primarily located below the hob surface. Removal of the hob is straightforward
by removing the control knobs, trivets, the burner caps and burner head assemblies and skirts. Using
a flat bladed screwdriver remove the five screws, one in each corner of the hotplates left and right spillage
bowls and one centrally located at the rear of the centre spillage bowl. Than lift the hob upwards.
Replacement is a reversal of the above procedure. Care must be taken to ensure that no damage occurs
to the spark ignition leads or the igniters. The electronic ignition pack is easily accessible for service or
replacement below the hob centrally at the ear.
ALWAYS ENSURE THAT THE POWER SUPPLY IS DISCONNECTED BEFORE SERVICING APPLIANCE
Gas Controls And Gas Manifold
Removal of the gas manifold is accomplished by removing the control knobs, the trivets, the
burner caps and burner head assemblies and skirts. Using a flat bladed screwdriver remove the five
screws, one in each corner of the hotplates left and right spillage bowls and one centrally located at the
rear of the centre spillage bowl. Care must be taken to ensure that no damage occurs to the spark ignition
leads, igniters or thermocouples (if fitted). Disconnect all ancillary gas piping. Remove the two securing
screws from the positioning brackets at the front and also the securing bracket near the gas inlet point to
the burner compartment. The gas manifold may than be extracted. Replacement is a reversal of the above
procedure.
ALWAYS ENSURE THAT THE GAS CONNECTION IS DISCONNECTED BEFORE SERVICING APPLIANCE
Conversion
If the appliance is to be used with another gas type, either ULPG Gas or Natural Gas, it must be converted
by an Authorised Person. Contact Eurolinx Pty Ltd or their unathorized agent for details. For Natural and
ULPG Gas Injector Sizes and Mj/H refer to tables on pages 39. The table above shows the
appropriate injector sizes for either ULPG Gas or Natural Gas.
NOTE
After conversion check the GAS PRESSURE and IGNITER OPERATION for the burners. If the hotplate
cooker cannot be adjusted to perform correctly, or if there is excessive flame discolouration, yellow tipping
or excessive noise contact ILVE or their authorised agent for advice. It is also recommended
that this appliance be serviced at 12 months minimum intervals or sooner as required. Please also ensure
that the duplicate data plate supplied be attached to the appliance or in an accessible place such as a
cupboard for future reference.
IMPORTANT:
Verify periodically the gas connection pipe and replace it as soon as any irregularity is present.
IMPORTANT: Correct positioning of the brass flame distributor is very important. For this purpose, ensure that
the flame distributor tooth coincides with the notch on the aluminum base. To keep the flame
distributor covers new, you are advised to remove them before lighting the flame.
ancillary service information
freestanding cookers
47ILVE Operating Manual
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ilve M-120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ilve M-120 in the language / languages: English as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info