666834
15
Zoom out
Zoom in
Previous page
1/19
Next page
7
ENGLISH
EN
When selecting the installation site the following
conditions must be assessed:
Installation not in potentially explosive atmos-
pheres
Installation not in ood-prone areas
Compliance with local technical connection re-
quirements and safety rules
The mounting surface should have a at and
sufciently rm ground
Humidity maximum 95% (non-condensing)
Ambient temperature of -25 °C to 40 °C
Average temperature within 24 hours < 35 °C
As a installation height: a distance of 50 to 150
cm is recommended from the ground to the lo-
wer housing edge
The charging socket on the vehicle should be
easily reachable with the tethered charging
cable or the charging cable intended for use.
The charging cable must not be under tension
when it is connected to the vehicle
It should not be possible to drive over the cable
3.3 Mechanical installation
The following tools and materials to install the ICU
Compact:
Spirit level
Impact Drill
Screwdriver for an M5 cross recess hole
Screwdriver for a terminal block
Pencil and provided drilling template
Torx M5 (T25)
Wire Stripper
Allen key
4 x screws M5 x 30 mm
4 x plugs M5 x 30 mm
4 x rings M5
4 x screws M8 x 20 mm
4 x rings M8
4 x screws M4 x 20 mm
4 x rings M4
Wall mounting: Drilling using the drilling
template
Please check the indicated dimensions with
a tape measure.
The distance between holes is 144 mm (horizon-
tal) and 312 mm (vertical).
NOTICE
1. Cut the drilling template from the cardboard pa-
ckaging
2. Place the template on the desired location
3. Check with a spirit level whether the template is
applied straight
4. Draw the drill holes using the template
5. Drill holes at the marked points
6. Check the drilled holes
Pole Mounting: Mounting the pole with the con-
crete base (optional):
1. Dig a hole about 50 x 50 cm with a depth of
50 cm
2. Attach the brackets at the bottom of the pole
with four M8 x 20 mm screws and four M8 ring
(see g. on the cover)
3. Now place the pole in the hole
4. Run the ground cable through the pedestal to
the charging station
5. Attach the cover plate to the pole using three
M5 x 13 mm screws and three M5 x 13 rings
6. Attach the holding of the charging cable on the
cover plate using four M4 x 12 mm screws
7. Fill the hole and pave the area
8. Cover the area afterwards with a clean trim
(e.g. tiles)
Installation of the charging station
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ICU Compact at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ICU Compact in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ICU Compact

ICU Compact User Manual - German - 18 pages

ICU Compact User Manual - Dutch - 8 pages

ICU Compact User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info