669927
15
Zoom out
Zoom in
Previous page
1/20
Next page
15
Inspect and tighten all parts of the elliptical exerciser
r
egularly. Replace any worn parts immediately.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. IMPORTANT: Keep liq-
u
ids away from the console and keep the console
out of direct sunlight. During storage, remove the
batteries from the console.
BATTERY REPLACEMENT
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
assembly step 3 on page 6.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed switch, you must remove the Left
Pedal Arm (11) and the Left Shield (3). Remove the
Pedal Arm Bolt Set (40), the M10 x 25mm Patch
Screw (22), the M10 Washer (35), and the Wave
Washer (58) from the Left Pedal Arm (11).
Remove the Left Pedal Arm (11). Next, remove the
two M4 x 25mm Screws (56) and the four M4 x 16mm
Screws (42) from the Left Shield (3). Then, remove
the Left Shield.
Locate the Reed Switch (53). Loosen, but do not
r
emove, the indicated M4 x 16mm Screw (42).
Slide the Reed Switch (53) slightly toward or away
from the Magnet (26) on the Flywheel (17). Then,
retighten the Screw. Turn the left Pedal Disc (15) for a
moment.
Repeat until the console displays correct feedback.
When the reed switch is correctly adjusted, reattach
the left shield and the left pedal arm.
HOW TO ADJUST THE DRIVE BELT
If the pedals slip while you are pedaling, even when
the resistance is adjusted to the highest setting, the
drive belt may need to be adjusted.
To adjust the Drive Belt (19), you must first remove
the left shield. See HOW TO ADJUST THE REED
SWITCH at the left and remove the left shield.
Next, loosen the
M8 x 22mm Flat
Head Screw (41)
and turn the
M10 x 60mm
Bolt (62) until the
Drive Belt (19) is
tight. When the
Drive Belt is tight,
tighten the Flat
Head Screw.
Then, reattach
the left shield.
MAINTENANCE AND TROUBLESHOOTING
42
56
42
42
42
22
58
3
40
15
17
41
62
19
35
11
26
53
42
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icon Cup X-Power E200 - AEVEL19008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icon Cup X-Power E200 - AEVEL19008 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Icon Cup X-Power E200 - AEVEL19008

Icon Cup X-Power E200 - AEVEL19008 User Manual - German - 20 pages

Icon Cup X-Power E200 - AEVEL19008 User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info