670299

Icom iPW1 Manual

5
Zoom out
Zoom in
Previous page
1/20
Next page
2
1
PANEL DESCRIPTION
q POWER SWITCH [POWER] (p. 11)
Push momentarily to turn power ON.
w TRANSMIT INDICATOR [TRANSMIT] (p. 13)
Lights green while transmitting.
During transmission, a humming may sound de-
pending on the output power. This is caused by
the large current produced by the power supply
and does not indicate equipment malfunction.
e ANTENNA TUNER INDICATOR [TUNER] (p. 13)
•Lights while the antenna tuner is activated.
•Blinks while tuning and the SWR becomes 1.5:1 or
greater on the 50 MHz band.
•Goes out after slow blinking when antenna turner
cannot tune the selected antenna (SWR 1.5:1 or
greater).
r ANTENNA TUNER SWITCH [TUNER] (p. 14)
•Turns the antenna tuner ON and OFF (bypass)
when pushed momentarily.
- The [TUNER] indicator lights while the antenna tuner is
activated; blinks while tuning.
- While operating in the 50 MHz band, the antenna tuner
does not start automatically. Push [TUNER] for 2 sec.
to tune the antenna manually.
•Starts to tune the antenna manually when pushed
for 2 sec.
- When the tuner cannot tune the antenna (SWR 1.5:1
or greater), the tuning circuit is bypassed automatically
after 20 sec.
t LINEAR AMPLIFIER SWITCH [AMP/PROTECT]
Turns the linear amplifier ON and OFF.
- The [AMP/PROTECT] indicator lights green when the
linear amplifier is ON. (p. 13)
- The [AMP/PROTECT] indicator lights red when the pro-
tector circuit is activated. (p. 14)
- When the linear amplifier is OFF, the [AMP/PROTECT]
does not light and the exciter’s signal is applied to one of
the output connectors or the IC-PW1’s antenna tuner.
y LOWER BAND SELECTOR [DOWN] (p. 13)
Selects the lower operating band when pushed.
u AUTOMATIC INDICATOR [AUTO] (p. 13)
Indicates that automatic band selection is activated.
(When an Icom CI-V transceiver is connected.)
i BAND INDICATORS (p. 13)
Indicate the selected operating band.
o UPPER BAND SELECTOR [UP] (p. 13)
Selects the higher operating band when pushed.
!0 OUTPUT ANTENNA SELECTOR [ANT] (p. 13)
Selects one of 4 output antenna connectors.
!1 INPUT ANTENNA SELECTOR [INPUT] (p. 13)
Selects one of 2 input antenna connectors.
!2 TRANSMIT METER-2 [METER-2]
Shows the final FET’s voltage (V
D
), SWR (Standing
Wave Ratio) or ALC (Automatic Level Control) level.
!3 TRANSMIT METER-2 SELECTOR
Selects the final FET’s voltage (V
D
), SWR (Stand-
ing Wave Ratio) or ALC (Automatic Level Control)
level for transmit meter-2.
!4 TRANSMIT METER-1 [METER-1]
Shows the RF output power (P
O
), final FET’s cur-
rent (I
D
) or heatsink temperature (TEMP).
!5 TRANSMIT METER-1 SELECTOR
Selects the RF output power (P
O
), final FET’s cur-
rent (I
D
) or heatsink temperature (TEMP) for trans-
mit meter-1.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom iPW1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom iPW1 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info