689583
397
Zoom out
Zoom in
Previous page
1/413
Next page
TROUBLESHOOTING
20-3
DOthers
PROBLEM POSSIBLE CAUSE SOLUTION REF.
Transceiver does not turn
ON.
The battery is exhausted.
The battery polarity is reversed.
Loose connection of a battery pack
(case).
Charge the battery pack, or replace the
batteries.
• Check the battery polarity in the case.
• Clean the battery terminals.
pp. 4-3, 4-4
p. 4-4
pp. 4-3, 4-4
No sound comes from the
speaker.
Volume level is too low.
An external speaker or a cloning cable
is connected to the [SP] jack.
Rotate [VOL] to adjust to a desired
level.
Check the external speaker connection
or remove the cloning cable.
p. 5-2
Sensitivity is too low, and
only strong signals are au-
dible.
The coaxial cable is not connected, or
shorted. (External antenna is used)
Check the coaxial cable connection or
replace with the new.
Transmitting is impossible. The transmit power level is set to S-
LOW, LOW1 or LOW2
The battery is exhausted.
The battery case is attached.
The PTT Lock function is activated.
The Busy Lockout function is activated.
Set the transmit power level to HIGH.
Charge the battery pack, or replace the
batteries.
Use the battery pack or external DC
power, and set the transmit power level
to HIGH.
Set the PTT Lock function to OFF in
the Function Menu.
Set the Busy Lockout function to OFF
in the Function Menu.
p. 5-11
pp. 4-3, 4-4
pp. 4-6, 5-10
p. 16-75
p. 16-75
No reply is received after a
call.
The duplex is set, and the receive and
transmit frequencies are different.
No station is in range or on the same
frequency.
Set the simplex operation.
Wait for a while, and try again.
p. 15-5
Transmitting using the VOX
function is impossible.
The VOX Level is set to OFF or too low.
The MIC Gain is too low.
Set the VOX Level to a suitable level.
Set the MIC Gain to a suitable level.
p. 16-77
p. 16-76
Contacting another station is
impossible.
A different tone or code is used for the
tone/DTCS squelch.
Check the tone/DTCS by performing a
tone scan.
p. 13-2
Frequency cannot be set. The Key Lock function is activated.
The memory mode, Call channel mode,
Weather channel mode* or DR function
is selected.
*USA version transceiver only
Hold down [LOCK] for 1 second to
cancel the Key Lock function.
Push [V/MHz] to select the VFO
mode.
p. 5-12
p. 5-10
A Program Scan does not
start.
The memory mode, Call channel mode,
Weather channel mode* or DR function
is selected.
*USA version transceiver only
The same frequency has been pro-
grammed in the scan edge channels,
A” and “B.”
Only one scan edge channel has been
programmed.
Push [V/MHz] to select the VFO
mode.
Program different frequencies in the
scan edge channels.
Program one or more pair of the scan
edge channels.
p. 5-10
p. 12-4
p. 12-4
A Memory Scan does not
start.
The Memory mode is not selected.
Only one or no memory channel has
been programmed.
Push [M/CALL] to select the Mem-
ory mode.
Program two or more memory chan-
nels.
p. 5-10
p. 12-4
The displayed frequency is
erroneous.
The CPU has malfunctioned.
• External factors have caused a fault.
• Reset the transceiver.
Remove and reattach the battery pack/
case.
p. 16-99
p. 1-2
Previous view
397


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom ID-51A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom ID-51A in the language / languages: English as an attachment in your email.

The manual is 66,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Icom ID-51A

Icom ID-51A Quick start guide - English - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info