689583
395
Zoom out
Zoom in
Previous page
1/413
Next page
20-1
TROUBLESHOOTING
The following chart is designed to help you correct problems which are not equipment malfunctions.
If you are unable to locate the cause of a problem or solve it through the use of this chart, contact your nearest Icom
Dealer or Service Center.
DWhile operating D-STAR
PROBLEM POSSIBLE CAUSE SOLUTION REF.
After your call, the repeater
does not return a status re-
ply.
The repeater setting is wrong.
The manually entered repeater fre-
quency, frequency offset, or duplex set-
ting is wrong.
Your transmission did not reach the re-
peater.
Select the correct repeater.
Correct the repeater frequency, fre-
quency offset, or duplex setting.
Wait until you are closer to the repeater
and try again.
Try to access another repeater.
p. 8-2
pp. 9-30, 9-31
After your call, the repeater
replies ‘UR?’ and its call
sign.
The call was successfully sent, but no
station immediately replied.
Wait for a while, and try again.
After your call, the repeater
replies ‘RX’ or ‘RPT?’ and
the access repeaters call
sign.
Your own call sign (MY) has not been
set.
Your own call sign (MY) has not been
registered on a gateway repeater, or the
registered contents do not match your
transceiver’s setting.
Set your own call sign (MY).
Register your own call sign (MY) on a
gateway repeater, or confirm the regis-
tration of the call sign.
p. 13 of the
Basic manual
p. 15 of the
Basic manual
After your call, the repeater
replies ‘RPT?’ and call sign
of the destination repeater.
The repeater cannot connect to the
destination repeater.
The repeater is busy.
Check the repeater setting.
Wait for a while, and try it again.
p. 9-23
After your call, the access
repeater replies ‘RPT?’ and
its call sign.
The call sign of the destination repeater
is wrong.
Correctly set the destination repeater
call sign.
p. 9-28
Even holding down , the
DR function is not selected.
There is no Repeater List in your trans-
ceiver.
Reload the Repeater List using the CS-
51PLUS2 cloning software on the CD.
Reload the Repeater List using a mi-
croSD card.
Enter the Repeater List data directly
into the transceiver.
p. 17-20
p. 8-21
p. 9-24
Even holding down , the
received call sign will not set
to the destination call sign.
The call sign has not been correctly re-
ceived.
When a received signal is weak, or a
signal is received during scanning, the
call sign may not be received correctly.
In that case, “--------” appears and error
beeps sound, and a reply call cannot be
made.
Try it again, after the transceiver has
correctly received the call sign.
A Local area call can be
made, but the Gateway call
or destination station call
cannot be made.
MY call sign has not been registered on
a D-STAR repeater.
Register your own call sign (MY) on a
gateway repeater, or confirm the regis-
tration of the call sign.
p. 13 of the
Basic manual
During transmission, “L ap-
pears on the LCD, and the
received audio is interrupted.
While receiving through the internet,
some packets may be lost due to net-
work error (poor data throughput per-
formance).
Wait a while, and try it again.
When the transceiver receives cor-
rupted data, and misidentifies it is as
Packet Loss, “L is displayed, even if it
is a Local area call.
“DV” and “FM” icons alter-
nately blink.
While in the DV mode, an FM signal is
received.
Use a different operating frequency un-
til there are no FM signals on the origi-
nal frequency.
p. 9-10
Previous view
395


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom ID-51A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom ID-51A in the language / languages: English as an attachment in your email.

The manual is 66,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Icom ID-51A

Icom ID-51A Quick start guide - English - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info