670150
251
Zoom out
Zoom in
Previous page
1/282
Next page
18-3
D Command table
18
CONTROL COMMAND
Cmd. Sub Cmd. Data Description
00 see p. 18-11 Send frequency data (transceive)
01 see p. 18-11 Send mode data (transceive)
02 see p. 18-13 Read band edge frequencies
03 see p. 18-11 Read operating frequency
04 see p. 18-11 Read operating mode
05 see p. 18-11 Set operating frequency
06 see p. 18-11 Operating mode selection for transceive
07 Select VFO mode
B0 Exchange the Main and Sub bands
B1 Equalize the Main and Sub bands
C2 00 or 01 Send/read the dualwatch setting
(00=OFF, 01=ON)
* Sub commands, C0 (dualwatch ON) and C1
(dualwatch OFF), are also usable for only
setting.
D2 00 Send/read Main band selection
* Sub command, D0, is also usable for only
setting.
01 Send/read Sub band selection
* Sub command, D1, is also usable for only
setting.
08 Select memory mode
0001 to
0099
Select memory channel
(0001=M-CH01, 0099=M-CH99)
0100 Select program scan edge channel P1
0101 Select program scan edge channel P2
09 Memory write
0A Memory to VFO
0B Memory clear
0E 00 Scan stop
01 Programmed/memory scan start
02 Programmed scan start
03 F scan start
12 Fine programmed scan start
13 Fine F scan start
22 Memory scan start
23 Select memory scan start
A1 Select F scan span ±5 kHz
A2 Select F scan span ±10 kHz
A3 Select F scan span ±20 kHz
A4 Select F scan span ±50 kHz
A5 Select F scan span ±100 kHz
A6 Select F scan span ±500 kHz
A7 Select F scan span ±1 MHz
B0 Set as non-select channel
B1 Set as select channel
( The previously set number by CI-V is set
after turning power ON, or “1” is selected if
no selection is performed.)
01
Set as select channel “1”
02
Set as select channel “2”
03
Set as select channel “3”
B2 00 Set “ALL” for select memory scan
01
Set “1” for select memory scan
02
Set “2” for select memory scan
03
Set “3” for select memory scan
D0 Set scan resume OFF
D3 Set scan resume ON
0F 00 or 01 Read split setting (00=OFF, 01=ON)
00 Turn the split function OFF
01 Turn the split function ON
10 00 Send/read tuning step OFF
01 Send/read 100 Hz tuning step
02 Send/read 1 kHz tuning step
03 Send/read 5 kHz tuning step
04 Send/read 9 kHz tuning step
05 Send/read 10 kHz tuning step
06 Send/read 12.5 kHz tuning step
07 Send/read 20 kHz tuning step
08 Send/read 25 kHz tuning step
Cmd. Sub Cmd. Data Description
11 00 Send/read attenuator OFF
03 Send/read 3 dB attenuator
06 Send/read 6 dB attenuator
09 Send/read 9 dB attenuator
12 Send/read 12 dB attenuator
15 Send/read 15 dB attenuator
18 Send/read 18 dB attenuator
21 Send/read 21 dB attenuator
12
00 00 or 01 Select/read ANT1 selection
(00=RX ANT OFF; 01=RX ANT ON)
01 00 or 01 Select/read ANT2 selection
(00=RX ANT OFF; 01=RX ANT ON)
02 00 or 01 Select/read ANT3 selection
(00=RX ANT OFF; 01=RX ANT ON)
03 00 Select/read ANT4 selection
(00=RX ANT OFF; fix)
13 00 Announce all data with voice synthesizer
01 Announce frequency and S-meter level with
voice synthesizer
02 Announce receive mode with voice
synthesizer
14
01 0000 to
0255
Send/read [AF] level
(0000=max. CCW, 0255=max. CW)
02 0000 to
0255
Send/read [RF] level
(0000=max. CCW, 0255=max. CW)
03 0000 to
0255
Send/read [SQL] level
(0000=max. CCW, 0255=max. CW)
05 0000 to
0255
Send/read [APF] level
(0000=Pitch–550 Hz, 0128=Pitch,
0255=Pitch+550 Hz; 10 Hz steps)
06 0000 to
0255
Send/read [NR] level
(0000=0%, 0255=100%)
07 0000 to
0255
Send/read inner [TWIN PBT] position
( 0000=max. CCW, 0128=center,
0255=max. CW)
08 0000 to
0255
Send/read outer [TWIN PBT] position
( 0000=max. CCW, 0128=center,
0255=max. CW)
09 0000 to
0255
Send/read CW pitch
( 0000=300 Hz, 0128=600 Hz, 0255=900 Hz;
5 Hz steps)
0A 0000 to
0255
Send/read [RF PWR] position
(0000=max. CCW, 0255=max. CW)
0B 0000 to
0255
Send/read [MIC] position
(0000=max. CCW, 0255=max. CW)
0C 0000 to
0255
Send/read [KEY SPEED] level
(0000=6 wpm, 0255=48 wpm)
0D 0000 to
0255
Send/read [NOTCH] position
( 0000=max. CCW, 0128=center,
0255=max. CW)
0E 0000 to
0255
Send/read COMP level (0000=0, 0255=10)
0F 0000 to
0255
Send/read [DELAY] position
(0000=2.0d, 0255=13.0d)
11 0000 to
0255
Send/read [AGC] level
(0000=max. CCW to 0255=max. CW)
12 0000 to
0255
Send/read NB level
(0000=0%, 0255=100%)
13 0000 to
0255
Send/read [DIGI-SEL] position
(0000=max. CCW to 0255=max. CW)
14 0000 to
0255
Send/read DRIVE gain
(0000=0%, 0255=100%)
15 0000 to
0255
Send/read Monitor gain
(0000=0%, 0255=100%)
16 0000 to
0255
Send/read VOX gain
(0000=0%, 0255=100%)
17 0000 to
0255
Send/read Anti VOX gain
(0000=0%, 0255=100%)
18 0000 to
0255
Send/read [CONTRAST] position
(0000=max. CCW to 0255=max. CW)
19 0000 to
0255
Send/read BRIGHT level
(0000=0%, 0255=100%)
Send/read data
251


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC7850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC7850 in the language / languages: English as an attachment in your email.

The manual is 15,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info