670412
6
Zoom out
Zoom in
Previous page
1/20
Next page
1
1 LCD DISPLAY
LCD display consists of 4 x 20 characters as shown.
Line 1: The incoming RSSI with 10 steps
Line 2: The output power levels with 10 steps
Line 3: The left 4 letters show channel numbers.
The middle 8 letters shows the channel name.
(If not programmed, it will be blank.)
The right 4 letters displays the status of the ra-
dio as described below.
a. RX mode:
M = Mix, both analog and digital can be
received
D = Only digital can be received
b. TX mode:
D = PTT digital transmission
A = PTT analog transmission
c. Monitor mode:
= Monitor off
S = Selective squelch
d. P25 squelch:
N = Normal squelch
S = Selective squelch
e. Low Voltage Icon:
= Low Voltage state (Icon flashes with
ALM LED)
f. Key lock mode:
= Key lock (Not displayed if in Low
Voltage alarm)
g. Shift mode:
= SHIFT KEY ICON (reverts to normal
within 2 seconds)
Line 4: The left 2 letters show GPC (GROUP CALL),
AC (ALL CALL), IC (INDIVIDUAL CALL). The
right 18 letters displays the GROUP NAME, IN-
DIVIDUAL NUMBERS, and so on.
2 LED DISPLAY
The IC-FR9010/FR9020 has 5 LED's from left to
right.
DIGI = The LED is ON when receiving a digital sig-
nal
REP = The LED is ON when in repeat mode
(The IC-FR9010/FR9020 can be programmed
for SIMPLEX - SEMIDUPLEX - DUPLEX -
REPEATER on a per channel basis.)
ALM = The LED flashes when an error on either TX
or RX occurs
TX = The LED is ON when in Transmit
BUSY = The LED is ON when receiving a signal
3 KEY CONTROLS
3.1 Key entry without [SHIFT] key
[0]–[9] = Channel numbers and individual call
address (target address)
[A] = P25 calls (Group Call, All Call, and
Individual Call)
[B] = The beginning and the end of indi-
vidual call number
[C] = TX Transmit mode (Clear or Secure),
only models with encryption
[D] = P25 mode (analog or digital TX)
[Q] = Cancel channel number, individual
number
[#] = Ending channel number, individual
number
[CH] = Channel number entry, depress CH,
then 0–9 for channels
[F] (Scan) = P25 Conventional Control Messages
(SBC)
[MON] = monitor ON or OFF
Rotary knob = Volume, Squelch, Back Light Dimmer
and Timer
3.2 Key entry following [SHIFT] key
[0] = P25 test mode start and finish
[1] = Backlight ON/OFF
[2] = TX power HIGH/LOW
[3] = Talkaround ON/OFF
[4] = Change
[5] = No function
[6] = No function
[7] = Indicates Analog channel data
[8] = Key lock ON/OFF
[9] = No function
[A] = Manual CWID send key
[B] = Programmed CWID Start/Stop key
[C] = Cryptogram Test
[D] = No function
[Q] = Indicating P25 data (while de-
pressed)
[#] = DTMF Entry
[CH] = Toggle Bar-Graph or TX RX Fre-
quencies
[F] (Scan) = SBC (Conventional Control Messag-
es) Log/Emergency Call
[MON] = P25 squelch normal or selective and
analog MONITOR modes
RX = = = = = = = = = =
TX = = = = = = = = = =
C001 TAC 2 MD N
GPC 500
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-FR9020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-FR9020 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info