670162
82
Zoom out
Zoom in
Previous page
1/180
Next page
Twin PBT operation
<MODE> SSB/CW/RTTY/PSK/AM
PBT (Passband Tuning) electronically narrows the IF
passband width by shifting the IF frequency slightly
outside of the IF filter passband to reject interference.
The IC-7600 uses DSP for the PBT function. Moving
both [TWIN-PBT] controls to the same position shifts
the IF both above and below the received frequency.
The LCD shows the passband width and shift fre-
quency graphically.
The indicator on the [PBT-CLR] switch lights when
PBT is in use.
Push and hold [FILTER] for 1 sec. to enter the filter
set screen. Current passband width and shift fre-
quency is displayed in the filter set screen.
To set the [TWIN-PBT] controls to the center posi-
tions, push and hold [PBT-CLR] for 1 sec.
The variable range depends on the passband width
and mode. The edge of the variable range is half
of the passband width, and PBT is adjustable in 25
(SSB/CW/RTTY/PSK modes) or 100 Hz (AM mode)
steps.
The [TWIN-PBT] controls should normally be set to
the center positions (PBT setting is cleared) when
there is no interference.
When PBT is used, the audio tone may be changed.
Not available for FM mode.
While rotating the [TWIN-PBT] controls, noise may
occur. This comes from the DSP unit and does not
indicate an equipment malfunction.
Push and hold [DEF] (F-4) for 1 sec. to select a
default value.
PBT operation example
PBT2
PBT1
PBT2
PBT1
PBT2
PBT1
IF center frequency Interference Desired signal
Passband
Both controls at
center position
Cutting the lower
passband edge
Cutting both lower and
higher passband edges
Interference InterferenceDesired signal
Passband
[TWIN-PBT]
PBT-CLR
FILTER
F-4
DEF
Shows filter width, shifting value and condition
• Filter set screen
“SHARP” is selected.
75
4
RECEIVE AND TRANSMIT
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7600 in the language / languages: English as an attachment in your email.

The manual is 14,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info