670162

Icom IC-7600 Manual

38
Zoom out
Zoom in
Previous page
1/180
Next page
D Band edge warning beep
When you tune inside or outside of an amateur band’s
frequency range, a warning beep sounds. (“ ”
may be indicated on outside of an amateur band’s fre-
quency.) (p. 14)
This function can be turned OFF in set mode, if desired.
q Push [EXIT/SET] several times to close a multi-
function screen, if necessary.
w Push [SET] (F-6) to select set mode menu screen.
• Pushing and holding [EXIT/SET] for 1 sec. also selects
set mode menu screen.
e Push [OTHERS] (F-5) to enter others set mode.
r Push [Y] (F-1) or [Z] (F-2) to select “Beep (Band
Edge).”
t Rotate the main dial to select the band edge warn-
ing beep function.
y Push [EXIT/SET] to exit the set mode.
The beep output level can be set in level set mode.
(p. 123)
When the band edge warning beep is set to “ON”:
The
band edge warning beep sounds (enter: Pi, exit:
Bu) according to the set mode setting as follows.
• ON (Default)
Band edge beep sounds when an operating frequency
enters or exits the default amateur band. (default)
• ON (User)
A beep sounds when an operating frequency enters or
exits an amateur band that is set in band edge screen.
• ON (User) & TX Limit
Same as the setting of “ON (User).” However, the
transmission can be made in the set frequency
range only.
To programming the band edge:
W
hen “ON (User)” or “ON (User) & TX Limit” is
selected, [BAND] appears in the display above the
function switch (F-5), and up to 30 band edge fre-
quencies can be set in band edge screen.
q
Perform the steps q to t as above, then select
“ON (User)” or “ON (User) & TX Limit.”
w Push [BAND] (F-5) to enter the band edge screen.
e Push [Y] (F-1) or [Z] (F-2) to select the desired
band edge.
• Push [Ω ≈] (F-3) to select the set content for band
edge, lower or upper.
•
Push [INS] (MF6) to
insert a new blank band edge line.
• Push and hold [DEL] (MF7) for 1 sec. to delete the
selected band edge l
ine.
• Push and hold [DEF] (F-4)
for 1 sec. to display the
band edge initialize screen. Then, push and hold
[OK] (F-5) to initialize all band edge frequency settings.
r Input the desired frequency with the keypad.
• Push [GENE •] to input “. (decimal point)” between the
MHz units and kHz units.
• Program the frequency in ascending order.
• The frequency that is duplicated or out of an amateur
band cannot be programmed.
t Push [EXIT/SET] to exit the set mode.
When the transverter function is in use, the band
edge warning beep sounds with the default setting.
Main dial
F-1 F-2
F-6
EXIT/SET
SET
F-5
OTHERS
Main dial
EXIT/SET
F-5
F-1 F-2 F-3 F-4
DEF
[INS][DEL]
Keypad
OK
/
BAND
• Band edge screen
NOTE: All frequency ranges are set in default. So
you should delete or change it to add the desired
band edge frequency.
ON (Default) (default)
31
3
BASIC OPERATION
ON (User)
Appears
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7600 in the language / languages: English as an attachment in your email.

The manual is 14,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info