670163

Icom IC-7300 Manual

130
Zoom out
Zoom in
Previous page
1/173
Next page
13
OTHER FUNCTIONS
13-4
Protection function
The transceiver has a 2 step protection function to
protectthenalpowerampliersincasetheantenna
SWR becomes high.
Thefunctiondetectsthepowerampliertemperature
and activates when the temperature becomes too
high.
Power down transmission
Reduces the transmission output power.
• “LMT”isdisplayedbelow while transmitting.
TX inhibit
Disables the transmitter.
•
TX
is displayed instead of while the transmitter is
disabled.
When the function is activated, wait until the power
ampliercoolsdownbyusingthetransceivertoonly
receive.
NOTE: Do not turn OFF the transceiver power when
the Protection function is activated. If you do, the
cooling fan will deactivate and it will take longer to
cool down.
• You can check the power
ampliertemperaturewith
the TEMP gauge in the Multi-
function meter.
TX inhibit zone
You can perform a rough frequency calibration by
receiving the radio station WWV, WWVH, or other
frequency signals.
REF adjustment
NOTE:
• The transceiver has been adjusted and tested
at the factory before being shipped out. You
should not have to re-calibrate.
• Before performing a frequency calibration, you
havetoset“CalibrationMarker”toON.
• Spurious signal waveforms may be displayed
while the Calibration Marker is ON.
L Before performing a frequency calibration, set the
following items as described in the table below.
AF RF/SQL
Decent audibility
AF RF/SQL
Maximum RF gain
TWIN PBT
CLR
Reset by holding down for 1 second.
Operating mode
USB
RIT
OFF (No RIT icon displayed)
1. Set the frequency to the standard frequency
station minus 1 kHz.
L If receiving WWV or WWVH (at 15.00000 MHz) as
your standard frequency, set the operating frequency
to 14.99900 MHz.
2. Set“CalibrationMarker”toON.
MENU
» SET > Function > Calibration Marker
3. Selectthe“REFAdjust”item.
MENU
» SET > Function > REF Adjust
4. Rotate
MULTI
to adjust for a zero beat with the
received standard signal.
L“Zerobeat”meansthattheexactsamefrequencies
are set to 2 signals, resulting in a single tone being
transmitted.
5. Set“CalibrationMarker”toOFF.
6. Push
EXIT
several times until the SET screen is
closed.
… 130 …


Need help? Post your question in this forum.

Forumrules
1

Forum

icom-ic-7300

Reset search

  • is there available a wiring pictorial chart for the small internal ic-7300 coaxial jumper cables?
    ie: from the RF unit to the PA board? tnx Sam in Alabam KF4TXQ Submitted on 2-1-2022 at 06:09

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7300 in the language / languages: English as an attachment in your email.

The manual is 24,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info