12320
52
Zoom out
Zoom in
Previous page
1/64
Next page
50
9
INSTALLATION AND CONNECTIONS
UT-106 DSP RECEIVE UNIT
Optional IF lters
The UT-106 provides AF DSP functions such as noise
reduction and auto notch.
q Remove the bottom cover.
w Slide the insulating case onto the UT-106 as
shown right. (Fig. 1)
e Remove the connection cable (P2601) from J2602
on the MAIN unit. Connect the cable into J1 on the
UT-106.
r Plug the connection cable (P1) from the UT-106 to
J2602 on the MAIN unit.
t Plug the flat cable into J3 on the UT-106 and to
J2603 on the MAIN unit.
Take care regarding the conductor direction.
y Turn the UT-106 unit over. (Fig. 2)
No need to x with an adhesive strip, etc.
u Put the UT-106 on the MAIN unit.
No need to x with an adhesive strip, etc.
Ensure that the surplus cable from UT-106 is stored
under the unit.
i Return the bottom cover to its original position.
UT-106
P 1 (from UT-106)
J 2602
J 2603
P 2601
insulating case
flat cable
MAIN unit
Turn the unit over
Several IF lters are available for the IC-718. You can
install 1 lter for 455 KHz IF. Choose the appropriate
lter for your operating needs. (pgs, 24-25)
D Installation
q Remove the bottom cover as shown on the p. 48.
w Remove 7 screws, connection cable p1 from J1,
p5 from J701, W4 from J4101 and W5 from J4001
and 2 Tr-clampers as shown in the diagram below.
e Install the desired 455 KHz lter as shown in the
diagram below.
r Mounting the lter with supplied washers and nuts.
t Solder the 4 leads.
y Return the MAIN unit and bottom cover to their
original positions.
After filter installation, specify the installed filter
using initial set mode. (p. 47) Otherwise, the in-
stalled lter will not function properly.
Tr-clamper
W 4
W 5
P 5
P 1
J 701
J 1
J 4101
MAIN unit
Tr-clamper
Optional IF filter
Solder 4 leads
J 2603
Main unit
Rear panel
UT-106
Flat cable*
insulating case
* Supplied with UT-106
UT-106
Surplus cable
J 2602
J 2602
Fig. 1
Fig. 2
Turn the unit over
IC-718.qxd 02.9.6 14:30 Page 50
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-718 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-718 in the language / languages: English as an attachment in your email.

The manual is 3,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info