813010
20
Zoom out
Zoom in
Previous page
1/24
Next page
20
Starting the stove
Open the stove door to activate the system. The system
will automatically go back to standby and the dampers
will be closed if lighting up does not occur within 
minutes.
Lighting up
Your new HWAM® SmartStove™ closes all valves when
not in use to prevent hot air from being sucked into the
chimney and out into the open (loss of energy). For the
HWAM® SmartStove™, this valve function comprises the
challenge that, at each new lighting, you will always
start out with a cold chimney - pay attention to this. It
requires extra rapid heating of the stove and chimney
when lighting the stove.
A proper lighting is best done with - kg. of firewood
chopped into - rather small pieces (the amount of
wood depends on the model - see the user manual for
instructions regarding the specific model). Then add
- pieces of fine kindling wood, and on top of it all,
place a couple of fire-lighters. Light up the firelighters
and close the door.
The HWAM® SmartControl™ starts when the combustion
chamber door is opened. The HWAM® SmartControl™
has a cold start-up program requiring that the operating
temperature is reached within  min. If the heat-up
is too slow, the app will ask for more firewood. This
may seem illogical when there is both firewood and
flames in the stove, but as long as the proper operating
temperature has not been reached, the stove does not
burn environmentally clean, and, therefore, the temper-
ature has to be reached fast. The reasons for a slow
rise in temperature may be: insucient draught in an
ancient brick chimney, damp firewood, too large fire-
wood pieces, or insucient firewood/kindling wood.
The following guide is an introduction as to how the HWAM® SmartStove™ is to be operated
from start to restoking and until the fire finally burns out. The stove is only EN-approved for
burning wood. It is recommended that you use dry split wood with a moisture content of a
maximum of %. Firing wet firewood causes soot, environmental pollution and bad fuel eco-
nomy. It is recommended that you purchase a moisture metre to verify that the wood has the
correct moisture content before being used for firing.
Firing process
IMPORTANT!
If the flue gases do not reach
a high enough temperature
for kindling or firing, HWAM®
SmartControlTM and the wire-
less room temperature sensor
emit a stoking alarm, even if
there is still unburned wood
and flames in the combustion
chamber. The stoking alarm
is emitted to make you aware
that the fire needs more
energy. Restoking with small
pieces of kindling wood can
often provide a more rapid
and sucient temperature
rise.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam SmartControl Generation 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam SmartControl Generation 2 in the language / languages: English as an attachment in your email.

The manual is 4.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam SmartControl Generation 2

Hwam SmartControl Generation 2 User Manual - German - 24 pages

Hwam SmartControl Generation 2 User Manual - Dutch - 24 pages

Hwam SmartControl Generation 2 User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info