613740
17
Zoom out
Zoom in
Previous page
1/44
Next page
17
Ligthing the fire:
The woodburning stove is ready to be lit and opens the dampers. The symbol
appears when you press the remote control twice in either standby or burning
out modes. The symbol is also shown if you press the remote control twice in the
burning out phase. In this case it does not mean that you need to light up again.
This is merely information that you have asked the stove to open the dampers
and thereby ensure that the new firewood gets sufficient air to catch fire.
The restoking alarm
When the combustion progresses to the ember phase, a restoking alarm will
go off. The alarm will light up three times with a ten second interval and it is
supported by sound.
Three different amounts of wood are recommended for restoking:
A small amount of wood (700 - 1200 g)
A medium amount of wood (1000 - 2000 g)
A large amount of wood (1800 - 3000 g)
You must use at least two pieces of firewood at a time, even if you only want to
use a small amount of wood. The temperature causes the wood to gasify. Two
pieces of firewood heat up each other and increase their temperature faster.
A reminder of the restoking alarm
If a restoking alarm has gone off, and no restoking has been carried out, this
symbol will flash on and off in the upper left corner.
If the symbol has been displayed for a long time, the temperature in the flue
gasses can be so low that you have to light up again in order to give the stove
more air (this is done by pressing the remote control twice, causing the lighting
up symbol to appear in the display).
Always be aware that the status line changes from the burning out phase to the
combustion process phase when the stove is relit. Thereby you ensure that the
stove has registered that you have added new firewood which requires an adequate
amount of air. The oxygen level in the combustion compartment increases when
the door is opened. This sends a signal to the stove that new firewood has been
added to the fire. Towards the end of the burning out phase, the oxygen level in the
combustion compartment can be so close to the oxygen level in the room that the
increase in the oxygen level in the combustion compartment due to the opening
of the door cannot be registered. If, shortly after relighting, the status line does
not alter from burning out phase to combustion process phase, you should press
the remote control twice until the lighting up symbol (the matchbox) appears.
Updating
When the Air box is updated with new software (by a service technician), this
will be displayed graphically.
Updating
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 3220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 3220 in the language / languages: English, Italian as an attachment in your email.

The manual is 3,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 3220

Hwam 3220 User Manual - German, Dutch, French - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info