627048
6
Zoom out
Zoom in
Previous page
1/32
Next page
6
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN WIJZI G I N GEN E N T YPE F O U TEN VOORB E H O UDEN
5.4 onderhoud
5.4.1 reInIgen
Verwijder al het vet van de machine. Maak alle bewegende delen goed schoon en smeer deze lichtjes.
5.4.2 olIe
Afbeelding 3, 4 en 5 – Olie
In de kop van de machine bevindt zich een oliepomp voor het smeren van de tandwielen (afb. 5).
Let op!
De machine wordt geleverd zonder olie!
De machine moet worden gevuld met Shell Tellus 46. Ga als volgt te werk om de machine met olie te vullen
(max. 4.5 liter):
Verwijder de oliestop bovenop de kop.
Gebruik een trechter om de olie bij te vullen.
Stop met olie bijvullen wanneer het niveau de rode lijn op het oliepeilglas bereikt. Het niveau mag nooit boven
de rode lijn uitkomen anders loopt de olie uit de machine. Mocht dit onverhoopt toch een keer gebeuren,
verwijder dan de oliestop aan de linkerkant van de kop en laat de olie weglopen (afb. 4), totdat het niveau zich
op of iets onder de rode lijn bevindt.
5.4.3 smerIng
Afbeelding 6 – Smering
A As van spindel. Smeer dagelijks de smeernippel naast de afdekking van de spiraalveer.
B Tandwielas van spindelhuls. Smeer dagelijks het oliepunt op de afdekking van de spiraalveer.
4
Drilling Machine Instruction Book
4
GENERAL DESCRIPTION
1 Driving motor 10 Manual control for gear box
2 Speed selectors 11 Deep stop
3 Speed plate 12 Rapid manual feed control
4 Oil filling opening 13 Oil filling opening
5 Oil pump control sight gage 14 Oil level window
6 Oil level window 15 Oil draining plug
7 Oil draining plug 16 Feed selector
8 Tool ejector 17 Automatic feed lever
9 Spiral spring housing
2 automatic feeds. Mechanical engagingdisengaging ,through lever.
FILLING WITH OIL
The speed box incorporates an oil pump to
lubricate the gears.
Attention! The machine is supplied without oil for
transport reasons .Please; follow the following
instructions for filling the machine with oil:
Remove upper plug .Fill oil by using a funnel. Stop
filling oil when oil level reaches the red mark on level
window .This red mark must be never exceeded, as
otherwise, the oil will overflow out the machine.
If this occurs, remove plug and drain oil until oil level
goes down to red mark on level window.
.
Fig 5
Fig 6
Fig 7
Drilling Machine Instruction Book
4
GENERAL DESCRIPTION
1 Driving motor 10 Manual control for gear box
2 Speed selectors 11 Deep stop
3 Speed plate 12 Rapid manual feed control
4 Oil filling opening 13 Oil filling opening
5 Oil pump control sight gage 14 Oil level window
6 Oil level window 15 Oil draining plug
7 Oil draining plug 16 Feed selector
8 Tool ejector 17 Automatic feed lever
9 Spiral spring housing
2 automatic feeds. Mechanical engagingdisengaging ,through lever.
FILLING WITH OIL
The speed box incorporates an oil pump to
lubricate the gears.
Attention! The machine is supplied without oil for
transport reasons .Please; follow the following
instructions for filling the machine with oil:
Remove upper plug .Fill oil by using a funnel. Stop
filling oil when oil level reaches the red mark on level
window .This red mark must be never exceeded, as
otherwise, the oil will overflow out the machine.
If this occurs, remove plug and drain oil until oil level
goes down to red mark on level window.
.
Fig 5
Fig 6
Fig 7
Drilling Machine Instruction Book
5
LUBRICATION
Quill Spindle Daily lubricate with oil the greaser located next the spiral
spring cover .
Quill gearing shaft Daily lubricate with oil the lubrication port on the spiral
spring cover.
Quill Clean and lubricate with grease the rack for upward and downward
displacement of quillspindle .
Column Clean and grease with oil every 50 hours.
Speed box Fill the box with oil until reaching the indicated level. Change oil
every 2000 hours.
Feed box Fill the box with oil until reaching the indicated level. Change oil
every 2000 hours.
Rack Clean and lubricate with grease every 50 hours.
Table Daily lubricate with oil the two lubrication points.
Fig 8 Fig 9
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 40 G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 40 G in the language / languages: Dutch as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 40 G

Huvema HU 40 G User Manual - English - 32 pages

Huvema HU 40 G User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info