627040

Huvema HU 30FP SUPER VARIO Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
11
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
8. troUbleShooting
Switch off power and remove plug from power source outlet before trouble shooting.
Problem Solution
Drill is caught in the work piece and the spindle
has stopped
1. Push the emergency button
2. Turn off the power
3. Turn the spindle manually counterclockwise to withdraw
the tool from the work piece
4. Clean any chips on the work piece.
5. Turn on the power again
6. Resume drilling slowly to test if the drill does not get caught
again and then return to normal feed
Supply of cutting liquid inadequate 1. Check if the pump is running
2. Check if the hose is leaking
Spindle shaft cannot run completely 1. Check the belt tension
2. If the tension is too little, adjust it
3. Replace worn belts
Motor does not work 1. Check the power and check if the machine is switched on
2. Check the power cable for damage. Replace damaged
cables directly.
Spindle shaft makes a lot of noise 1. Check the bearing
2. Check if the v belt tension is too high; this will cause noise.
Drill oscillation 1. Check chuck condition
2. Make sure the drill is properly fixed in the chuck
9. FeeD ShaFt SPring tenSion
The feed shaft return spring is set at the factory; however, during the life of the drill press you may want to adjust the
spring so that the feed shaft return pressure suits your operating needs.
5-1. Feed Shaft Spring Tension:
The feed shaft return spring is adjusted at thefactory; however, during the life of the drill pressyou may
want to adjust the feed shaft returnspring so the feed shaft return pressure suits youroperating needs.
To adjust the feed shaft spring tension:
1. UNPLUG THE DRIL PRESS !
2. Wipe off any oil on the spring lock cover so itdoes not slip in your fingers when you hold the
cover from spinning (see Figure 28).
3. While holding the spring lock cover against the side of the head stock so the cover stayssplined with
the locking lug; loosen the jam nut and loosen the cover nut approximately1⁄4" (see Figure 30).
4. Put on heavy leather gloves to protect your hands from possible lacerations if the springuncoils
during the next step.
5. Pull the cover outward just enough to disengage the spring-cover lock slot from thelocking lug. Note:
It is important to keep a good grip during this step. Letting go of thecover will cause the spring to
rapidly uncoil.
6. Rotate the cover counterclockwise to increase spring tension, or let the cover slowly unwind in the
clockwise direction to reduce spring tension.
7. Engage the next available spring-cover lock slot with the locking lug and hold the springlock cover
tightly against the side of the headstock.
8. Snug the cover nut against the spring cover just until the nut stops, and then back offthe nut
approximately 1⁄3 turn, or just enough so there is no binding at complete spindletravel.
9. Hold the cover nut and tighten the jam nut against the cover nut.
21
Figure 27
Figure 29
Figure 30
Figure 28
Lock Nut
Spring Lock
Cover
Spring Cover
Lock Slot
Screw
Wrench
Size 19mm
Figure 17
Figure 18
Figure 19
Borgmoer
Figure 20
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 30FP SUPER VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 30FP SUPER VARIO in the language / languages: English as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 30FP SUPER VARIO

Huvema HU 30FP SUPER VARIO User Manual - German - 20 pages

Huvema HU 30FP SUPER VARIO User Manual - Dutch - 20 pages

Huvema HU 30FP SUPER VARIO User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info