Manual Huvema HU 16 F HS-4 TOPLINE (page 7 of 16) (Dutch)

627044

Zoom out

Zoom in

1/16

WIJZIGINGEN EN TYPEFOUTEN VOORBEHOUDEN WIJZIGINGEN EN TYPEFOUTEN VOORBEHOUDEN

7.1. TaFelhoogTe InsTellen

Afbeelding 4

U stelt de tafelhoogte in door de tafelvergrendeling (table lock) los te maken en de tafel met de hendel

voor de tafelverstelling (table height adjustment) op de gewenste hoogte te plaatsen. Maak vervolgens de

tafelvergrendeling weer vast.

7.2. Kop draaIen

Zorg ervoor dat de voet van de machine verankerd is om te voorkomen dat de machine omvalt wanneer u de

kop draait.

• Maak de hendel van de kopvergrendeling los en zet de kop in de gewenste positie.

• Maak de hendel weer stevig vast.

7.3. Kop In hoogTe versTellen

• Maak de bouten onder de kop los en zet de kop op de gewenste hoogte.

• Maak de bouten weer stevig vast.

Ga hierbij voorzichtig te werk, de kop is zwaar en de kolom heeft geen tandheugel voor de kopverstelling.

8. smerIng

Alle kogellagers zijn in de fabriek gesmeerd met vet. Ze hoeven verder niet gesmeerd te worden. Smeer wel

regelmatig de groeven in de spindel en de vertanding (van de spindelhuls).

9. onderhoud

• Blaas het stof in de ventilator van de motor regelmatig weg.

• Wanneer u de tafel en kolom van een dunne laag was voorzien blijven deze langer schoon.

9.1. v-snaar vervangen

• Start de machine en laat deze even op de hoogste snelheid draaien. Hierdoor ligt de v-snaar los genoeg om

gemakkelijk verwijderd te worden.

• Schakel de machine geheel uit en ontkoppel deze van de netspanning.

• Verwijder de v-snaarbeschermkap.

• Verwijder de v-snaar.

• Plaats de nieuwe v-snaar en plaats de beschermkap weer terug.

• Sluit de machine weer aan op de netspanning en start de machine weer.

Lubrication

Following are lubrication recommendations for drill press

components.

1. Spindle pulley drive: Lubricate spindle splines

occasionally with light grease.

2. Quill, Table, and Column: Lubricate with light film of

oil.

3. Table lift rack: Lubricate regularly with SAE20 oil

(clean rack with solvent before applying oil.)

4. Variable speed drive fork: Lubricate contact points

occasionally with grease.

Adjustments

Table Adjustment

The table can be raised or lowered to accommodate the

height of the component being drilled (refer to Figure 4). To

raise or lower the table, loosen the lock handle. Then use

the hand crank to move the table to the desired height.

Then retighten the lock handle.

Figure 4. Table Adjustment

Head Adjustment

WARNING: CHANGE THE RADLAL POSITION OF

THE DRILL HEAD ONLY IF THE DRILL PRESS

BASE IS SECURED TO THE FLOOR. SWINGING

THE DRILL HEAD WITHOUT THE BASE BEING

SECURED TO THE FLOOR WILL CAUSE THE

DRILL PRESS TO BECOME UNSTABLE AND TIP

OVER RESULTING IN INJURY AND/OR DAMAGE

TO THE MACHINE.

The radial position of the drill head can be changed to

accommodate the drilling of a hole that may be offset from

the center of the table. Reposition the drill head by

loosening the locking handles and swinging the drill head to

the desired position. Then retighten the locking handles.

Wiring Diagram

Refer to Figure 5 for wiring information. The drive motor can

be set up for 115/230 volt single phase or for three phase

power.

Figure 5. Wiring Diagram

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 16 F HS-4 TOPLINE in the language / languages: Dutch as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Huvema HU 16 F HS-4 TOPLINE Manual

Product: