627044

Huvema HU 16 F HS-4 TOPLINE Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
6
WIJZIGINGEN EN TYPEFOUTEN VOORBEHOUDEN WIJZIGINGEN EN TYPEFOUTEN VOORBEHOUDEN
Afbeelding 2
6. dIepTe-aanslag
Afbeelding 3
De diepte-aanslag bevindt zich aan de rechterzijde van de kop. U stelt de aanslag in door de onderste moer naar de
gewenste diepte te draaien, af te lezen op de schaalverdeling op de diepte-aanslag en vervolgens de bovenste moer
vast tegen de onderste moer aan te draaien.
7. geBruIK
Voordat u de machine gebruikt, moet u de handleiding zorgvuldig doorlezen om vertrouwd te raken met de
constructie, de bedieningselementen en het aandrijfmechanisme van de machine.
• Plaats de boor ver genoeg in de boorkop om de boor goed vast te kunnen zetten tussen de bekken. De boorkop is
zelfcentrerend.
• De boordiepte kunt u instellen met de diepte-aanslag, zie afbeelding 3.
• U wijzigt de toerentallen door de beschermkap van de v-snaar te openen en het gewenste toerental te kiezen
volgens de tabel in de kap.
5
Figure 2. Operating Controls
Depth Stop
A drilling depth stop (refer to Figure 3) is provided on the
right side of the drill head. The depth stop consists of a
threaded rod with depth setting jam nuts. The front side of
the threaded rod has a depth scale. The jam nuts are
loosened and moved to the desired depth on the scale. The
upper jam nut is then tightened against the lower nut.
Figure 3. Depth Stop
Operating Precautions
The following operating and safety precautions must be
observed in order to avoid harm to the operator or damage
to the drill press.
1. The head assembly must be locked to the column so
the thrust produced by drilling will not force the head
assembly up the column.
2. The work table must be locked to the column so it will
not be forced down the column.
3. Be sure the belt is tightened to the proper tension.
4. DO NOT start to drill the work-piece until making
certain the work-piece is held down securely.
5. MAKE SURE THE DRIVE MOTOR IS RUNNING
BEFORE turning the speed control hand-wheel in
either direction.
6. Point of operation protection is required for maximum
safety. This remains the responsibility of the
user/purchaser since conditions differ between jobs.
7. Make sure the drill is secured in the spindle or check
before attempting to use the drill press.
8. Make sure the spindle taper is clean and free of burrs,
scoring, and galling to assure maximum gripping.
Drilling Recommendations
Speeds for Drilling
The speed of a drill is usually measured in terms of the rate
at which the outer periphery of the tool moves in relation to
the work being drilled. The common term for this is Surface
Feet per Minute (SFM). The relationship of SFM is
expressed in the following formulas:
SFM = 0.26 X rpm X Drill Diameter (in inches)
RPM = 3.8x SFM
Drill diameter (in inches)
In general, the higher the speed the shorter the drill life.
Operating at the low end of the speed range for a particular
material will result in longer lift. The most efficient speed for
operating a drill depends on many variables:
1. Composition and hardness of material.
2. Depth of the hold.
3. Efficiency of the cutting fluid.
4. Type and condition of the drilling machine.
5. Desired quality of the hole.
6. Difficulty of set-up.
5
Figure 2. Operating Controls
Depth Stop
A drilling depth stop (refer to Figure 3) is provided on the
right side of the drill head. The depth stop consists of a
threaded rod with depth setting jam nuts. The front side of
the threaded rod has a depth scale. The jam nuts are
loosened and moved to the desired depth on the scale. The
upper jam nut is then tightened against the lower nut.
Figure 3. Depth Stop
Operating Precautions
The following operating and safety precautions must be
observed in order to avoid harm to the operator or damage
to the drill press.
1. The head assembly must be locked to the column so
the thrust produced by drilling will not force the head
assembly up the column.
2. The work table must be locked to the column so it will
not be forced down the column.
3. Be sure the belt is tightened to the proper tension.
4. DO NOT start to drill the work-piece until making
certain the work-piece is held down securely.
5. MAKE SURE THE DRIVE MOTOR IS RUNNING
BEFORE turning the speed control hand-wheel in
either direction.
6. Point of operation protection is required for maximum
safety. This remains the responsibility of the
user/purchaser since conditions differ between jobs.
7. Make sure the drill is secured in the spindle or check
before attempting to use the drill press.
8. Make sure the spindle taper is clean and free of burrs,
scoring, and galling to assure maximum gripping.
Drilling Recommendations
Speeds for Drilling
The speed of a drill is usually measured in terms of the rate
at which the outer periphery of the tool moves in relation to
the work being drilled. The common term for this is Surface
Feet per Minute (SFM). The relationship of SFM is
expressed in the following formulas:
SFM = 0.26 X rpm X Drill Diameter (in inches)
RPM = 3.8x SFM
Drill diameter (in inches)
In general, the higher the speed the shorter the drill life.
Operating at the low end of the speed range for a particular
material will result in longer lift. The most efficient speed for
operating a drill depends on many variables:
1. Composition and hardness of material.
2. Depth of the hold.
3. Efficiency of the cutting fluid.
4. Type and condition of the drilling machine.
5. Desired quality of the hole.
6. Difficulty of set-up.
LED Speed Display Toerentaldisplay
Speed control handwheel Handwiel snelheid
On/Off switch Aan/uit-schakelaar
Depth stop Diepte-aanslag
Jam nuts Moeren
Depth scale (on threaded
rod)
Diepte-aanduiding
(op stang)
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 16 F HS-4 TOPLINE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 16 F HS-4 TOPLINE in the language / languages: Dutch as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info