Manual Husqvarna Z560X (page 19 of 280) (English, German, Dutch, French, Italian, Spanish)

733969

Zoom out

Zoom in

1/280

Mowing Tips

• Find and ag rocks and other xed objects to

avoid collisions.

• Begin with a high cutting height and reduce

it until the desired mowing result is attained.

Cut the average lawn to 63.5 mm during the

cool season and over 76.2 mm during the hot

months. For healthier and better looking lawns,

mow often after moderate growth.

• For best cutting performance, mow grass over

15.2 cm in height twice. Make the rst cut

relatively high; the second to the desired height.

• The mowing result will be best with a high

engine speed (the blades rotate rapidly) and

low speed (the rider moves slowly). If the grass

is not too long and dense, the driving speed can

be increased without negatively aecting the

mowing result.

• When mowing large areas, start by turning to

the right so that clippings will discharge away

from shrubs, fences, driveways, etc. After one

or two rounds, mow in the opposite direction

making left hand turns until nished.

• The nest lawns are obtained by mowing

often. The lawn becomes more even and the

grass clippings more evenly distributed over

the mown area. The total time taken is not

increased as a higher operating speed can be

used without poor mowing results.

• Avoid mowing wet lawns. The mowing result

is poorer because the wheels sink into the soft

lawn, clumps build, and grass clippings fasten

under the cowling.

• Hose the mower deck underside with water

after each use. When cleaning, the mower deck

shall be raised into the transport position. Make

sure the mower is cooled and the engine is o.

• Use compressed air to clean top surface of

the deck. Avoid ooding water on top surface,

engine and electrical components.

• When the mulching kit is used, it is important

that the mowing interval is frequent.

WARNING! Do not make adjustments

unless:

• the engine is stopped,

• the ignition key is removed,

• the park brake is engaged

Moving Machine By Hand

Bypass Valves

Bypass valves are used to release the system so

the machine may be moved by hand when not

running.

Hydro Pumps

When pushing or pulling the mower, engage

the bypass valve on each transaxle. Access to

the valves is from the lower rear of the unit. The

bypass valves are located on the front, inner

sides of the transaxles. Set the deck to the lowest

position when accessing the pump valves. To

disengage each pump, turn the slot on the pump

valve 45

clockwise from the RUN position to the

BYPASS position.

Load the machine into truck or trailer by driving up

ramps in low gear. DO NOT LIFT! The machine is

not intended to be lifted by hand.

WARNING! Use extreme caution when

loading the machine into a truck or trailer using

ramps. There is the possibility of serious injury

or death if the machine falls o the ramps.

• Try not to stop or change speed on hills.

• Make all turns slowly.

WARNING! Do not drive the rider on

terrain that slopes more than 10 degrees. Mow

slopes up and down, never side to side. Avoid

sudden directional changes.

OPERATION

What type fluids go in the two containers near the fuel tanks? Submitted on 4-6-2022 at 21:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Z560X in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 49,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna Z560X Manual

Product: