477575

Husqvarna YTH151 Manual

57
Zoom out
Zoom in
Previous page
1/72
Next page
57
6
3
8
4
2
02
4
6
7
1
2
4
3
Dismantling of the cutting unit
Work from the right side of the machine.
1. Take off the belt from the engine pulley (1).
2. Remove the small retainer spring (2) and lift clutch spring
off the pulley bolt.
3. Remove the large retainer spring (3), slide collar off and
push housing guide out of the bracket.
4. Remove the two rear retainer springs (4) and knock off
the axle taps with a hammer.
Demontage des Mähdecks
Arbeiten Sie auf der rechten Seite der Maschine.
1. Entfernen Sie den Riemen von der Keilriemenscheibe
des Motors (1).
2. Entfernen Sie den kleinen Splint (2) und ziehen Sie die
Kupplungsfeder von der Achse des Riemenrades ab.
3. Entfernen Sie den großen Splint (3), ziehen Sie den
Kranz ab, und drücken Sie das Führungsgehäuse aus
der Verankerung heraus.
4. Entfernen Sie die beiden hinteren Federklammern (4)
und entfernen Sie die beiden Bolzen.
Depose du Carter de Coupe
Effectuer l'intervention à partir du côté droit du tracteur.
1. Sortir la courroie d'entraînement de la gorge de la poulie
motrice (1).
2. Retirer le petit ressort de tension (2), et décrocher le res-
sort d'embrayage des lames du coté du boulon ser vant
d'axe à la poulie d'embrayage.
3. Retirer l'épingle (3), faire glisser le collier et repousser
le guide à l'extrémité de la gaine pour le faire sortir du
support.
4. Retirer les deux épingles fi xant les bras de suspension
arrière et sortir les bras en tapotant sur leur axe à l'aide
d'un marteau.
Desmontaje de la unidad de corte
Trabajar desde el lado derecho de la máquina.
1. Quitar después la correa de la polea del motor (1).
2. Remueva el resorte de retención pequeño (2), y levante
el resorte del embrague hacia fuera del perno de la
polea.
3. Remueva el resorte de retención grande (3), deslice el
collar hacia fuera y empuje la guía del bastidor hacia
afuera del soporte.
4. Quitar los dos resortes posteriores (4) y golpear con un
martillo los muñones de eje hasta sacarlos.
Smontaggio del piatto di taglio
Lavorare sul lato destro della macchina.
1. Togliere la cinghia dalla puleggia del motore (1).
2. Rimuovere la piccola molla di fermo (2) e rimuovere, sol-
levando, la molla della frizione dal bullone della puleg-
gia.
3. Rimuovere la grande molla di fermo (3), estrarre il collare
e spingere la guida dell’alloggiamento fuori dalla staffa.
4. Togliere le due coppiglie (4) posteriori e con un martello
togliere anche i perni.
Demonterhen van de maaikast
Werk vanaf de rechter kant van de machine.
1. Haal daama de riem van de poelie van de motor (1).
2. Verwijder de kleine borgveer (2) en licht de veer van de
aandrijfkoppeling omhoog van de katrolbout af.
3. Verwijder de grote borgveer (3), schuif de kraag eraf en
duw de geleider van de behuizing uit de beugel.
4. Verwijder de twee achterste haarpinveren (4) en sla met
een hamer de twee as-pennen los.
(LTH151)
(YTH151)
1
2
4
3
… 57 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna YTH151 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna YTH151 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info