474766

Husqvarna WB48S Manual

15
Zoom out
Zoom in
Previous page
1/92
Next page
English – 15
MAINTENANCE
• Adjust the belt by moving the ball-bearing up or down.
• A new belt stretches and becomes longer, so adjust the
belt again after a few hours of operation.
• Screw on the belt cover and test run the machine.
Replacing and adjusting the centre belt
The centre belt runs between the engine shaft and the
gearbox.
• Remove the cutter. (only when replacing belt)
• Unscrew the adjuster screws a few turns.
• Replace the belt with a new one and tighten the
adjustment screws a little. (only when replacing belt)
• Adjust the belt by moving the gear forwards or backwards.
• The belt should be stretched so that it can move 10mm in
the centre. That corresponds to a pull of approx. 3 kg. Use
a fishing scale to check.
• Tighten the adjustment screws properly.
When changing the belt, refit the cutter with a torque of 45-60
Nm. See instructions under the heading Assembly.
• Check the drive operation, as adjustment of the gear
affects the belt tension in the gearbox.
Cleaning
Do not use a high pressure washer to clean the machine.
Never flush water directly on the engine.
When cleaning under the cutting hood, turn the machine with
the spark plug upwards. Empty the fuel tank.
Trouble shooting
If the engine does not start, check the following:
• Replace the fuel with new, clean fuel.
• Check that the fuel valve is open.
• Check that the engine brake works correctly and is
undamaged.
• Clean the spark plug. Check that the electrode gap is 0.7-
0.8 mm.
• Check the airfilter and clean it when it´s necessary.
• If the engine does not start after taking these actions,
contact the nearest authorised service agent.
• If the cutting result is not satisfactory and the grass straws
are fuzzy on the cut face, replace the cutter.
Below you will find some general maintenance
instructions.
Daily maintenance
1 Check that the engine brake handle works safely.
2 Brush leaves, grass and the like off of the lawn mower.
3 Clean the air intake on the starter. Check the starter and
starter cord.
4 Check the oil level.
5 Clean the air filter. Replace if necessary.
6 Check that nuts and screws are tight.
7 Check the cutting attachment. Never use blades that are
dull, cracked or damaged.
Weekly maintenance
1 Clean the spark plug. Check that the electrode gap is 0.7-
0.8 mm.
2 Clean the cooling fins on the cylinder.
Monthly maintenance
1 Check that drive belt is not damaged and is not visibly
defective.
2 Clean the gearbox.
3 Check the fuel filter and the fuel hose. Replace if
necessary.
4 Clean the inside of the fuel tank.
5 Lubricate the drive control.
6 Change the engine oil.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna WB48S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna WB48S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info