474766

Husqvarna WB48S Manual

14
Zoom out
Zoom in
Previous page
1/92
Next page
14 – English
MAINTENANCE
If the cutter hits foreign objects such as stones, roots or the
like the cutter will slip against the cutter bracket. This may
mean that the contact surface of the cutter bracket appears
slightly worn, which is completely normal. This is a safety
device, which reduces the risk of the engine shaft becoming
bent.
Changing the oil
The engine oil should be changed the first time after 5 hours
running time.
The engine oil should be changed each year and every 25
working hours.
When changing the oil proceed as follows::
• Disconnect the HT lead from the spark plug.
• Empty the fuel tank
• Close the fuel tap.
• Unscrew the oil filler cap.
Place a suitable vessel to collect the oil in.
• Drain the oil by tipping the engine so that the oil runs out
through the filler pipe.
• Ask where you can dispose of surplus engine oil at your
local petrol station.
• Fill with new engine oil of a good quality. See the Technical
data section.
• Now insert the dipstick again, without tightening it.
Check the oil level with the dipstick on the oil filler cap. If
the oil level is low, fill using engine oil up to the upper level
on the dipstick.
• Screw on the oil filler cap.
Drive and gearbox
Ensure the wheels and wheel axles are clean and free from
leaves, grass, etc. It is also important to keep clean around
the drive gearbox.
• Remove the protective cover by unscrewing the screws.
• Clean the gearbox with a brush. Also check that the drive
belt and belt pulley are undamaged, for example, no
cracks.
Replacing and adjusting the V-belt
• Remove the protective cover by unscrewing the screws.
• Remove the hubcap on the front wheel by the gearbox,
prize carefully with a screwdriver. Unscrew the carriage
bolt and remove the wheel.
• Remove the belt from the deck belt pulley. Check that the
deck belt pulleys move easily on the axle, spray with
penetrating oil between and behind the pulleys and
grease the axle.
• Fit the new belt and make sure it fits correctly by the ball-
bearing before adjusting the belt.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna WB48S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna WB48S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info