518172
13
Zoom out
Zoom in
Previous page
1/48
Next page
A
C
D
B
D
C
G ting Ready to Sew – 13
THREADING FOR TWIN NEEDLES
Press the ON/OFF switch to OFF.
1. Insert a twin needle.
2. Use a second thread spool or wind a bobbin with the thread
you are going to use as the second upper thread.
3. Lift the spool pin up and all the way to the right. Lock the
spool pin in the vertical position by slightly pressing it down.
Slide on the large spool cap. For spools smaller than the
medium size spool cap, place a felt pad under the thread spool.
4. Place the À rst thread spool on the spool pin. The spool should
rotate in a clockwise direction when the thread reels off the
spool.
5.
LEFT NEEDLE: Thread the machine as described on page 13.
Check to ensure that the thread lies between the left thread
tension discs (A). Thread the left needle manually.
6. Pull out the auxiliary spool pin and slide on the large spool
cap. For spools smaller than the medium size spool cap, place
a felt pad under the thread spool.
7. Place the second thread on the spool pin. The second spool
should rotate in a counterclockwise direction when the thread
reels off the spool.
8.
RIGHT NEEDLE: Thread the machine as before but this thread
should lie between the right thread tension discs (A) and
outside the needle thread guide (B). Thread the right needle
manually.
Note: Only use symmetrical twin needles (C). Do not use this type of twin
needle (D), since it may damage your sewing machine.
WINDING THE BOBBIN WITH
THE MACHINE THREADED
Make sure that the presser foot is up and the needle is in the
highest position.
Note! Do not use a plastic presser foot when bobbin winding.
1. Place an empty bobbin on the bobbin spindle on the top
of the machine. The bobbin only À ts on one way, with the
logo facing up. Use only original HUSQVARNA VIKING®
bobbins.
2. Pull the thread from the needle under the presser foot and to
the right through the thread guide (C).
3. Guide the thread through the hole in the bobbin (D) from the
inside to the outside.
Note: When using an earlier version of HUSQVARNA VIKING®
bobbins that do not have a hole, wind several turns of thread on the bobbin
to get started.
4. Push the bobbin spindle to the right. A pop-up message
appears on the GraphicDisplay. Press the foot control to start
winding. Hold the end of the thread À rmly when starting to
wind. Once the bobbin begins to wind, cut the excess thread.
When the bobbin is full, it will stop automatically. Push the
bobbin spindle back to the left, remove the bobbin and cut off
the thread on the thread cutter.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TRIBUTE 140C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TRIBUTE 140C in the language / languages: English as an attachment in your email.

The manual is 4,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna TRIBUTE 140C

Husqvarna TRIBUTE 140C User Manual - German - 48 pages

Husqvarna TRIBUTE 140C User Manual - Dutch - 48 pages

Husqvarna TRIBUTE 140C User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info