477663

Husqvarna TR430 Manual

23
Zoom out
Zoom in
Previous page
1/60
Next page
23
3
Inset A
Fig ure 9
10
Figure 10
Inset B
20
19
Inset C
d
e
pth_sta
k
e_
2
18
17
13
14
15
16
1. Outer side shield
2. Nut "A"
3. Nut "B"
4. Drive control lever
5. Drive control release
6. Handle
7. Throttle control
8. Fuel Valve
9. Starter handle
10. Shift lever in di ca tor
11. Depth stake
12. Depth Stake pin
13. Transport po si tion
14. Shallowest till ing
15. Shallow tilling
16. Deep tilling
17. Deepest tilling
18. Depth stake
19. "Release" po si tion
20. "Lock" position
Reverse
a. Release the drive control lever (fig. 9).
b. Move throttle control (fig. 9) to slow Position
c. Place shift lever indicator (fig. 10 -inset A) in the "R"
(reverse) position.
d. Do not stand directly behind tiller.
e. To start tiller movement, push down on the drive control
release and squeeze the drive control lever (fig. 9). Tines
will not turn.
WARNING!
Don't back yourself into a solid obstruction such as a tree,
fence, etc.
Stopping tines and engine
a. Tiller movement and tines will stop when drive control
lever (fig. 9) is released.
b. Move shift lever indicator (fig. 10 -inset A) to "N" (Neutral)
position.
c. To stop engine, move throttle control (fig. 9) to slow
position and allow the engine to run at low speed for 1
or 2 minutes before moving throttle to stop position.
d. Close the fuel valve (fig. 9).
e. Pull the starter handle (fig. 9) slowly and return the handle
to its original position when reistance is felt. This operation
is necessary to prevent outside moist air from intruding
into the combustion chamber.
Turning
a. Release the drive control lever (fig. 9).
b. Move throttle control (fig. 9) to "SLOW" po si tion.
c. Place shift lever indicator (fig. 10 - inset A) in "F" (forward)
position. Tines will not turn.
d. Lift handle to raise tines out of the ground (fig. 9)
e. Swing the handle in the opposite direction you wish to
turn, being careful to keep feet and legs away from the
tines.
When you have completed your turn-around, lower the handle.
Place shift lever in di ca tor in (
) (tilling) position and move
throttle control to desired speed. To begin tilling, push down
on the drive control release and hold drive control lever
against the handle.
Outer side shields
The back of the outer side shields (fig. 9) are slotted so that
they can be raised for deep tilling and lowered for shallow
tilling to protect small plants from being buried. Loosen nut
"A" in slot and nut "B". Move shield to desired position (both
sides). Retighten nuts.
Transporting
a. Lower the depth stake to its lowest position and insert
the depth stake pin in the topmost hole.
b. Place shift lever indicator (fig. 10 inset A) in "F" (foward)
position for transporting.
c. To start tiller movement, push down on the drive control
release and squeeze the drive control lever (fig. 9). Tines
will not turn.
d. Move throttle control (fig. 9) to desired speed.
1
2
9
6
4
5
3
7
8
depth_stake_
1
11
12
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna TR430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna TR430 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info