734468

Husqvarna ST 427T Manual

10
Zoom out
Zoom in
Previous page
1/200
Next page
4. Put the rotator head on the pin (E), and the threaded
stud (G) on the bracket (E).
A B
C
E
F
D
G
J
I
H
5. Attach a locknut (B) on the threaded stud and
tighten.
6. Attach the square retainer (I) with a locknut (H).
7. For ST 424/427/430 only: Put the cables through the
cable holder (C)
To install the discharge chute lever and
the release cable
1. Push the knob (D) down on the discharge chute
lever. Use a rubber mallet if it is necessary.
2. Attach the release cable to the discharge chute lever
at connection (A).
C
E
F
A
B
D
3. Put the release cable in the groove (B) on the
discharge chute lever.
4. Install the cable barrel fitting (F) to the release lever
(E).
5. Install the release lever (E) to the discharge chute
lever and attach it with the roll pin (C).
6. Adjust the release cable. See
To adjust the release
cable of the discharge chute on page 24
.
7. Adjust the left and right discharge chute cables. See
To adjust the left and right discharge chute cables on
page 24
.
To install the remote control for the
discharge chute deflector
1. Attach the cable bracket (A) to the discharge chute
with a carriage bolt (B) and a 5/16-18 locknut (D).
Tighten the bolt.
2. Install the cable eyelet (E) to the discharge chute
deflector (F). Use a shoulder bolt (G), a nylon
washer (C), and tighten with a ¼-20 locknut (K). The
cable eyelet will be loose on the shoulder bolt.
3. Attach the spring (L) between the hex nut (M) on the
rotator head and the hole on the discharge chute
deflector.
F
L
M
B
A
D
K
C
E
G
To install the speed control cable
1. Put the drive speed lever in the neutral position.
2. Attach the speed control cable (B) to the drive speed
lever with a retaining pin.
3. Attach the speed control cable to the bracket (C)
with 2 ½ in wrenches. Make sure that the drive
speed lever stays in the neutral position.
10 891 - 005 - 08.01.2020
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna ST 427T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 427T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info