610267
15
Zoom out
Zoom in
Previous page
1/48
Next page
15
1
A
B
C
A
B
C
A
B
C
Getting ready to sew
Winding the bobbin using the vertical
spool pin
1. Place an empty bobbin on the bobbin spindle at the front of
the machine (the Husqvarna Viking mark facing up). Use only
the original Husqvarna Viking bobbins.
2. Place the large spool holder and a felt pad under the spool on
the main spool pin set in the vertical position.
3. Bring the thread over and behind the pre-tension thread
guide (A) and down around the thread tension disc (B), then
through thread guide (C) as illustrated.
4. From above, wind a few turns of thread clockwise around
the bobbin. Push the bobbin spindle to the right. Cut off the
thread on the thread cutter.
5. Press the foot control to start winding. When the bobbin is
full it will stop automatically. Push the bobbin spindle back
to the left. Remove the bobbin and cut off the thread on the
thread cutter.
Winding the bobbin using the auxiliary
spool pin
1. Place an empty bobbin on the bobbin spindle at the front of
the machine (the Husqvarna Viking mark facing up). Use only
the original Husqvarna Viking bobbins.
2. Fold out the auxiliary spool pin. Place a large spool holder and
a felt pad under the spool.
3. Bring the thread over and behind the pre-tension thread
guide (A) and down around the thread tension disc (B), then
through thread guide (C) as illustrated.
4. From above wind a few turns of thread clockwise around
the bobbin. Push the bobbin spindle to the right. Cut off the
thread on the thread cutter.
5. Press the foot control to start winding. When the bobbin
is full the winding will stop automatically. Push the bobbin
spindle back to the left. Remove the bobbin and cut off the
thread on the thread cutter.
Placing the bobbin in the machine
Turn off the main switch
1. Remove the bobbin cover by sliding it towards you.
2. Place the bobbin in the bobbin case with the Husqvarna
Viking mark facing up. The bobbin will then rotate counter
clockwise when you pull out the thread.
3. Place your nger on the bobbin to keep it from turning as you
pull the thread rmly to the right and then to the left into the
tension spring (A) until it ‘‘clicks’’ into place.
4. Continue threading around (B) and into the thread cutter (C).
Replace the cover (1). Pull the thread to the left to cut it (2).
NOTE: Depending on the type of thread, wrap the
thread one or two turns around the bobbin thread
tension disc (B) to put more tension on the thread.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Sappire 850 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Sappire 850 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info