610265

Husqvarna Prisma 940 Manual

19
Zoom out
Zoom in
Previous page
1/62
Next page
General
hints
The
best
way
to
hold
the
fabric
is
to
let
your
left
hand
rest
lightly
on
the
work
at
A
and
guide
it
forward.
Hold
the
edge
of
the
fabric
at
B
with
your
right
hand
and
guide
the
work.
Do
not
pull
the
fabric—-just
guide
it
toward
the
presser
foot
and
let
the
machine
do
the
feeding.
When
you
wish
to
sew
straight
stitch,
place
the
work
so
that
the
needle
goes
down
in
the
center
of
the
marking
for
the
seam.
When
sewing
zig-zag
and
other
wide
stitches,
e.g.
overlock
stitches
place
the
marking
for
the
seam
along
the
left
edge
of
the
needle
hole.
Turn
your
work
so
that
the
larger
amount
of
fabric
is
placed
to
the
left
of
the
needle.
In
some
cases
it
is
necessary
to
mirror
the
stitch
in
order
to
obtain
the
required
result.
To
do
this,
press
the
mirroring
button
and
the
light
above
the
symbol
will
go
on.
Lower
the
presser
foot,
start
the
rniichine
gently
and
increase
the
speed
gradually.
When
sewing
fine
and
soft
fabrics,
start
the
seam
a
couple
of
mm
(1/8”)
from
the
edge
of
the
fabric,
to
prevent
it
from
being
pulled
down
into
the
needle
hole.
If
you
wish
to
extend
the
seam
out
to
the
very
edge
of
the
fabric,
sew
a
few
reverse
stitches
and
then
hold
the
threads
behind
the
presser
foot
when
sewing
forward
again.
When
sewing
a
long
seam,
where
you
must
stop
often
to
arrange
the
work,
or
when
you
wish
to
pivot
at
a
corner,
allow
the
needle
to
stop
at
its
lower
position.
Fasten
off
the
seam
by
depressing
the
reverse
feed
button
and
sewing
a
few
reverse
stitches.
When
the
seam
is
finished,
raise
the
presser
foot,
remove
the
work
from
behind
and
cut
off
the
threads
leaving
at
least
15
cm
(6’)
of
thread.
[B=o
1
rj
19
… 19 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-prisma-940

Reset search

  • Please clear and explain about hosquarna prisma 940adaptor including voltage and current thanks a lot
    Mohamadlajevardi@gmail.com Submitted on 15-12-2022 at 17:49

    Reply Report abuse

  • Please clear and explain about hosquarna prisma 940adaptor including voltage and current thanks a lot
    Mohamad lajevardi@gmail.com Submitted on 15-12-2022 at 17:47

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Prisma 940 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Prisma 940 in the language / languages: English as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info