610264

Husqvarna Prelude 360 Manual

18
Zoom out
Zoom in
Previous page
1/32
Next page
I..—
Sewing
Buttons
1.
Mark
the
fabric
where
the
hutton
is
to
he
located.
2.
Turn
the
stitch
selector
to
zigzag
\/v.
3.
Lower
the
feed
teeth
.
See
page
11.
4.
Snap
ofT
the
presser
ftx)t.
5.
Place
the
material
under
the
presser
foot
ankle.
6.
Place
the
button
on
marking
and lower
the
presser
bar
so
that
the
presser
foot
ankle
is
between
the
holes
of
the
button
(see
picture).
7.
1
bid
the
thread
ends
to
one
side.
‘him
the
handwheel
and
check
to
be
sure
that
the
needle
goes
into
the
holes
of
the
button.
8.
Sew
5-6
stitches.
Set
the
stitch
width
dial
to
0
and
lock
the
threads
with
a
few
stit
ches.
tise
the
clearance
plate
for
this
purpose.
Use
the
thin
end
when
sewing
buttons
on
light
fabrics,
the
thick
end
for
heavier
fabrics.
Push
in
the plate
between
the
button
and
the
fabric,
lower
the
presser
bar
and
sew
on
the
button,
Pull
the
threads
between
the
button
and
the
fabric.
Wind
the
threads
a
few
times
around
the
shank
and
tie
the
ends.
Cutting
Buttonholes
Cut
buttonhole
open
with
the
seam
ripper.
Place
a
straight
pin
across
the
end
you
are
cutting
toward
to
avoid
cutting
too
far!
j
16
… 18 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-prelude-360

Reset search

  • How do I change from buttonhole mode to straight sewing. Machine will only sew a very short stitch. Submitted on 20-9-2023 at 04:41

    Reply Report abuse

  • How do I lower the feed teeth on Husqvarna Viking prelude 360? Submitted on 3-8-2022 at 02:23

    Reply Report abuse

  • How do I lower the feed teeth on Husqvarna Viking prelude 360 Submitted on 3-8-2022 at 02:22

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Prelude 360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Prelude 360 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info