610264

Husqvarna Prelude 360 Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
Procedures
Threading
the
Upper
Thread
Make
sure
the
presser
toot
is
raised
and
the
needle
is
in
the
up
position
1.
Pull
the
spool
pin
out.
l’lace
the
thread
on
the
spooi
pin
and
the
spool
holder
on
the
spool
pin
as
described,
Push
the
spool
pin
back
in.
2.
Bring
the
thread
in
the
direction
of
the
arrow
under
the
thread
guide
(a)
and
over
the
thread
guide
(b).
3.
Bring
the
thread
down
between
the
thread
tension
discs.
4.
Continue
threading
by
drawing
the
thread
from
the
right
into
the
slot
(in
the
take—up
lever.
5.
Thread
last
guide
just
above
the
needle.
6.
The
needle
is
threaded
from
front
to
hack.
The
white
on
the
presser
toot
ankle
makes
it
easy
to
see
the
eye
of
the
needle.
7.
Place
thread
under
the
presser
foot
and
into
the
thread
knife
where
it
is
cut.
Bobbin
Winding
with
the
Machine
Threaded
Make
sure
that
the
presser
foot
is
up
and
the
needle
is
in
the
highest
position.
Note!
Do
not
use
a
plastic
presser
foot
when
bobbin
winding.
1.
Place
your
empty
bobbin
with
the
small
mark
outwards
on
the
bobbin
spindle
on
the
front
of
the
machine.
Bring
the
Note!
We
do
not
recommend
winding
spe
bobbin
spindle
down.
cialty
threads
such
as
clear
nylon
or
other
2.
Pull
the
thread
from
the
needle
under
stretchy
threads
through
the
needle.
Instead
the
presser
foot
and
to
the
right
over
the
see
“Bobbin
winding
—
vertical
spool
pin”.
thread
guide
(c).
3.
Start
from
above
and
wind
a
kw
turns
of
thread
around
the
bobbin.
Cut
off
the
thread
on
the
thread
knife
(d).
4.
Press
the
foot
control.
When
the
bobbin
winding
is
finished,
remove
the
bobbin,
cut
off
the
thread
and
bring
the
bobbin
spindle
up.
7
… 9 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-prelude-360

Reset search

  • How do I change from buttonhole mode to straight sewing. Machine will only sew a very short stitch. Submitted on 20-9-2023 at 04:41

    Reply Report abuse

  • How do I lower the feed teeth on Husqvarna Viking prelude 360? Submitted on 3-8-2022 at 02:23

    Reply Report abuse

  • How do I lower the feed teeth on Husqvarna Viking prelude 360 Submitted on 3-8-2022 at 02:22

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Prelude 360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Prelude 360 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info