518134
21
Zoom out
Zoom in
Previous page
1/44
Next page
19
Functions and GraphicDisplay
The stitch width is automatically
adjusted to fi t the set twin needle width.
The stitch settings remain until the twin
needle function is turned off.
The twin needle function is active until
you cancel it, even if your Platinum 770
is turned off. Touch the twin needle
button and set the value to “0” to turn
off the function.
Mirror Side to Side
Touch this button to mirror the selected
stitch side to side. If this button is
pressed when straight stitch with left
needle position is selected, the needle
position is changed from left to right. If
touched in REP, the whole stitch combi-
nation is mirrored (see page 30).
If you try to mirror a stitch that cannot
be mirrored, Platinum 770 beeps.
Mirror End to End
Touch this button to mirror the selected
stitch end to end. If touched in REP, the
whole stitch combination is mirrored
(see page 30). If a STOP is programmed
at the end of a combination, and the
combination is mirrored end to end, the
STOP will be placed at the beginning
instead.
If you try to mirror a stitch that cannot
be mirrored, Platinum 770 beeps.
The Functions Panel
Stitch length
When you select a stitch, your Platinum
770 automatically sets the best stitch
length. The set length is visible on the
GraphicDisplay above the stitch length
button. You can change the stitch length
by pressing either the (+) or (-) button.
Some stitches have a limited stitch
length. Minimum and maximum settings
are indicated with a “beep” signal.
Stitch width
The stitch width is set in the same way
as the stitch length. The set width is
visible on the GraphicDisplay above
the stitch width button. The width can
be adjusted between 0 and 6 mm. If
straight stitch is selected, the width
button is used to adjust the needle posi-
tion. Some stitches have a limited stitch
width. Minimum and maximum settings
are indicated with a “beep” signal.
Twin needle
When pressing this button, a pop-up
message appears on the GraphicDisplay,
prompting you to set the twin needle
width. Select the width by touching the
selection buttons. A twin needle icon is
shown in the upper left corner of the
GraphicDisplay. Touch the button again
to see the current twin needle setting.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Platinum 770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Platinum 770 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info