595368
25
Zoom out
Zoom in
Previous page
1/48
Next page
English – 25
MAINTENANCE AND SERVICE
Maintenance schedule
The following is a list of the maintenance which should be conducted on the machine. For those points not described in this manual,
visit an authorised service workshop.
1)
First change after 25 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.
2)
Maintenance and replacement are required more often in dusty conditions.
3)
First change after 25 hours.
4)
Conducted by
authorised service workshop.
X = Described in this operator's manual
O = Not described in this operator's manual
!
WARNING! No service procedures must be conducted on the engine or cutting unit unless:
The engine is switched off.
The parking brake is applied.
The ignition key is removed.
The cutting unit is disengaged.
Maintenance
Daily maintenance Maintenance interval in hours
Before
starting
After work is
completed
10 40 100 200 400 800
Check the safety system X
Check for fuel and oil leakage. O
Check the engine’s oil level X X
Check coolant level and antifreeze. X X
Checking the transmission oil level X X
Check and clean the engine’s cooling air intake, clean the radiator. X X
Cleaning X
Start engine and blades, listen for noise O
Check nuts and screws O
Clean underside of cutting unit X
Lubricate throttle cable X
Grease the blade shafts X
Check air filter X
Check the tyre pressures. X
Lubricate according to lubrication schedule, see under heading
"LUBRICATION"
X X
Clean thoroughly around engine X
Clean thoroughly around transmission X
Clean the air filter and empty the particle collector X
Checking the blades X
Replace the fuel filter. X
Change engine oil and filter
1)
X
1)
Check the synchronisation between the front and rear wheels. O
Change hydraulic oil and hydraulic filter
3, 4)
. O
3, 4)
Check oil level in the bevel gear, top up if necessary. X
Check belt tension and condition (alternator belt, PTO belt, cutting
unit belt)
X
Check the battery condition, clean as necessary. X
Clean transmission air intake X X
Check the wheel nuts. O
Check the parking brake X
Replace the air filter
2)
. X
2)
Change belts (PTO belt and cutting unit belt). X
Change the oil in the bevel gear. X
Change pump and alternator belt X
Change coolant (50% glycol). X
Service at an authorised service representative. O
IMPORTANT! When the machine is in operation the hoses are under high pressure. Do not try to connect or disconnect the hoses
when the hydraulic system is operational. This can result in serious personal injuries.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna P 520D - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P 520D - 2015 in the language / languages: English as an attachment in your email.

The manual is 12,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna P 520D - 2015

Husqvarna P 520D - 2015 User Manual - German - 48 pages

Husqvarna P 520D - 2015 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info