610257
8
Zoom out
Zoom in
Previous page
1/52
Next page
Instruction book/Manual de instrucciones Lily 535
8
3
1
2
Connecting the foot
control
Among the accessories you will find the foot
control cord and the main cord.
1. Place the foot control on its narrow side. Fit the
plug into the socket inside the foot control
compartment.
2. Push it firmly to make sure it is properly con-
nected. This operation is only necessary the
very first time you are going to use the
machine.
3. To correctly turn away the cord, place it into
the slot, see picture.
Note: Before plugging in, check to ensure that
the foot control is of "type FR2".
Connecting to the
power supply
On the underside of the machine you will find
information about the power supply (V) and the
frequency (Hz). Check the power supply setting in
the machine to ensure that this agrees with the
main supply before you
connect the machine.
1. Connect the foot control
cord to the first socket on
the bottom right side of
the machine.
2. Connect the main cord to
the back socket on the
bottom right side of the
machine.
3. When you press the power
switch, both the machine
and the light are switched on.
For the USA and Canada
This Sewing Machine has a polarized plug (one
blade wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a pola-
rized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the
proper outlet. Do not modify the plug in any way.
Conexión del pedal
El cable del pedal está entre los accessorios. Este
cable ha de conectarse al mando de pie.
1. Ponga de canto el pedal. Introducir la clavija
pequeña en el zócalo dentro del mando de
pie.
2. Controlar que la clavija de contacto está bien
fija. Esto solo ha de hacerse la primera vez,
cuando se desembala la máquina.
3. Para poder desenrollar correctamente el cable,
colóquelo en la ranura según la figura.
1. Conectar el cable del
pedal en la entalladura
de delante abajo en el
lado derecho de la
máquina.
2. Conectar el cable de la
red en el enchufe trasero,
debajo del lado derecho
de la máquina.
3. Al pulsar el interruptor
principal, se conecta la
máquina y la ilumina-
ción.
Para los Estados Unidos y el Canada:
Esta máquina de coser tiene un enchufe polarizado
(tripolar). Para reducir el riesgo de choque eléctrico este
enchufe encaja a un enchufe de pared polariza-do de una
sola manera. Si el enchufe no encajara bien en el enchufe
de pared, de la vuelta al enchu-fe. Si todavía no encaja
bien, contacte a un electri-cista calificado para instalar un
enchufe apropriado. No modifique de ninguna manera el
enchufe.
!
Atención! Controlar que el pedal tiene la
marca "type FR2".
Conexión eléctrica
Debajo del zócalo están indicadas la tensión
(voltaje) y la frecuencia (Hz). Antes de conectar la
máquina a red, asegurarse de que los valores
indicados coincidan con los de la red.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Lily 535 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Lily 535 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info