Manual Husqvarna LC 353AWD (page 15 of 404) (All languages)

733941

Zoom out

Zoom in

1/404

6. If you do not see a leak, start the engine. Let the

engine run until the product is clean below the

housing.

7. Stop the engine.

8. Stop the water supply and remove the hose from the

water hose connection.

Note: Do not remove the water hose from the water

hose connection while the engine is in operation.

Water in the engine can decrease the life of the

engine.

9. Start the engine and let it run for a full minute to

remove remaining water from the product.

To replace the engine oil

WARNING: Engine oil is very hot directly

after the engine is stopped. Let the engine

become cool before you drain the engine oil.

If you spill engine oil on your skin, clean with

soap and water.

1. Operate the product until the fuel tank is empty.

2. Remove the ignition cable from the spark plug.

3. Remove the oil tank cap.

4. Put a container below the product to collect the

engine oil in.

5. Tilt the product to drain the engine oil from the oil

tank.

6. Fill with new engine oil of the type recommended in

Technical data on page 19

7. Do a check of the oil level. Refer to

To do a check of

the oil level on page 11

To examine the spark plug

CAUTION:

Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:

a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.

c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, refer to

Technical data

on page 19

. (Fig. 41)

• Replace the spark plug if it is necessary.

To clean the air filter

1. Remove the air filter cover and remove the filter.

2. Hit the filter against a flat surface to make the

particles fall off.

CAUTION: Do not use solvent or

compressed air to clean the air filter.

3. Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

4. Put the air filter cover back.

Note: An air filter that is used for a long time cannot be

fully cleaned. Replace the air filter at regular intervals.

Always replace a damaged air filter.

To examine the cutting equipment

WARNING: To prevent accidental start

remove the ignition cable from the spark

plug.

WARNING: Use protective gloves when you

do maintenance on the cutting equipment.

The blade is very sharp and cuts can easily

occur.

1. Examine the cutting equipment for damage or

cracks. Always replace a damaged cutting

equipment.

2. Look at the blade to see if it is damaged or blunt.

Note:

It is necessary to balance the blade after it is

sharpened. Let a service center sharpen, replace and

balance the blade. If you hit an obstacle that causes the

product to stop, replace the damaged blade. Let the

service center estimate if the blade can be sharpened or

must be replaced.

To assemble the blade

1. Put the blade adapter on the engine crankshaft.

Make sure the key in the adapter and crankshaft

keyway are aligned.

(Fig. 42)

2. Always attach the blade with the angled ends

pointing up in the direction of the engine.

(Fig. 43)

3. Use a block of wood between the blade and product

housing. Tighten the blade bolt and turn it clockwise.

4. Always tighten the bolt with a torque of 35-40 ft lbs

(47-54 Nm).

(Fig. 44)

5. Make sure the spark plug cable is disconnected from

the engine.

CAUTION:

To prevent accidental start,

always disconnect the spark plug cable

1242 - 003 - 01.11.2019 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 353AWD in the language / languages: All languages as an attachment in your email.

The manual is 8,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna LC 353AWD Manual

Product: