733941

Husqvarna LC 353AWD Manual

13
Zoom out
Zoom in
Previous page
1/404
Next page
1. Push the cutting height control in the direction of the
wheel and then rearward to increase the cutting
height.
2. Push the cutting height control in the direction of the
wheel and then forward to decrease the cutting
height. (Fig. 28)
CAUTION: Do not set the cutting height too
low. The blades can hit the ground if the
surface of the lawn is not level.
To start the product
1. Stay behind the product.
2. Hold the engine brake handle against the handlebar.
(Fig. 29)
3. Hold the starter rope handle with your right hand.
4. Slowly pull out the starter rope until you feel some
resistance.
5. Pull with force to start the engine.
WARNING: Do not twist the starter rope
around your hand.
To use the drive on the wheels
• Pull the drive levers in the direction of the handlebar.
(Fig. 30)
• Before you pull the product rearward, disengage the
drive and push the product forward approximately
10cm.
• Release the drive levers to disengage the drive, for
example when you go near an obstacle.
To adjust the drive control cable
• Use the adjuster screw to adjust the drive control
cable. (Fig. 31)
• Turn off the engine. Always disconnect the spark
plug before you operate the movable parts.
• Turn the adjustment screw counterclockwise to
tension the wire and increase the speed.
• Turn the adjustment screw clockwise to extend the
wire and reduce speed.
To stop the product
• To stop the drive only, release the drive levers.
• To stop the engine, release the engine brake handle.
(Fig. 32)
To use the product with the grass
catcher
WARNING: Do not operate the product
without a grass catcher installed or without
the rear deflector closed. Objects can eject
and cause injury to the operator.
1. Lift the rear deflector and remove the mulch plug.
(Fig. 33)
2. Assemble the grass catcher, refer to
To assemble
the grass catcher on page 12
.
3. Put the grass catcher on the bracket. (Fig. 34)
4. Release the rear deflector and put it on top of the
grass bag frame.
To change the product to mulching
mode
The mulching mode of the product makes grass
clippings smaller. The grass clippings then fall onto the
lawn and scatter across the grass. Mulched grass
biodegrades quickly to give nutrients for the lawn.
1. Lift the back shield and remove the grass bag, if it is
installed.
2. Put the mulch plug into the collector channel.
(Fig. 35)
3. Let the back shield close and make sure it tightly
closes against the mulch plug.
(Fig. 36)
To change the product to rear-side
discharge mode
1. Lift the rear deflector and remove the mulch plug.
(Fig. 37)
2. Install the discharge chute. (Fig. 38)
To empty the grass catcher
CAUTION: Do not drag the bag when you
empty the grass catcher to prevent wear.
1. Lift the grass catcher with the frame handle. (Fig. 39)
2. Remove grass clippings from the grass catcher from
below the handle.
3. Empty grass clippings from the bag with the frame
handle and the bag handle.
To get a good result
• Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
• Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
• Cut in different directions each time to prevent
stripes in the lawn.
1242 - 003 - 01.11.2019
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 353AWD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 353AWD in the language / languages: All languages as an attachment in your email.

The manual is 8,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info