595370
29
Zoom out
Zoom in
Previous page
1/92
Next page
MAINTENANCE
English 29
Replacing the blades
Dismantling:
Unscrew the bolt holding the cutter.
Remove the old blade. Make sure the blade bracket is
free of damage. Also check that the cutter bolt is
undamaged and that the engine shaft is not bent.
Assembly:
The blade must be mounted with the angled ends
pointing up towards the cover.
Make sure the cutter centres correctly on the shaft.
Fit the washer and tighten the bolt correctly. The bolt
should be tightened with a torque of 45-60 Nm.
Pull the blade around by hand and make sure it
rotates freely.
Test run the machine.
Spark plug
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking other steps.
If the spark plug is dirty, clean it and check that the
electrode gap is 0.5 mm. Replace if necessary.
Air filter
Remove the air filter cover and take out the filter.
Remove the foam plastic filter. Wash the filter well in
tepid soapy water. After cleaning, rinse the filter well
in clean water. Squeeze out and allow the filter to dry.
NOTE! High pressure compressed air can damage
the foam.
After cleaning the filter should be oiled using engine
oil. Wipe away excess oil by pressing a clean cloth
against the filter.
An air filter that has been in use for a long time cannot
be cleaned completely. The filter must therefore be
replaced with a new one at regular intervals.
A
damaged air filter must always be replaced.
When reassembling, make sure that the filter
completely seals against the filter holder.
Fuel system
Check that the fuel cap and its seal are not damaged.
Check the fuel hose. Replace if necessary.
CAUTION! Prevent unintentional starting by removing
the ignition cable from the spark plug.
IMPORTANT!
Always exercise care and use your common sense.
Avoid all situations which you consider to be beyond
your capability. If you still feel uncertain about operating
procedures after reading these instructions, you should
consult an expert before continuing. Contact an
authorised service workshop.
Always use genuine parts. For more information, see
the ”Technical data” section.
NOTICE! Always use the recommended spark plug
type! Use of the wrong spark plug can damage the
piston/cylinder.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 140S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 140S in the language / languages: English, German, French, Italian, Swedish as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna LC 140S

Husqvarna LC 140S User Manual - All languages - 324 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info