595370
28
Zoom out
Zoom in
Previous page
1/92
Next page
MAINTENANCE
28 – English
General
Let your Husqvarna dealer regularly check the
machine and make essential adjustments and repairs.
Replace any damaged, worn or broken parts.
Always use genuine accessories.
Maintenance schedule
In the maintenance schedule you can see which parts of
your machine that require maintenance, and with which
intervals it should take place. The intervals are calculated
based on daily use of the machine, and may differ
depending on the rate of usage.
*See instructions in the section "Machine’s safety
equipment".
General inspection
Check that nuts and screws are tight.
External cleaning
Brush leaves, grass and the like off of the lawn mower.
Do not use a high pressure washer to clean the
machine.
Never flush water directly on the engine.
Clean the air intake on the starter. Check the starter
and starter cord.
When cleaning under the cutting cover, empty the fuel
tank and put the machine with the spark plug
upwards.
Oil level
The lawn mower should stand on flat ground when you
check the oil level. Check the oil level with the dipstick on
the oil filler cap.
Remove the oil cap and wipe the dipstick clean.
Put the dipstick back in. The oil filler cap must be
completely screwed down to give a correct picture of
the oil level.
If the oil level is low, fill using engine oil up to the upper
level on the dipstick.
Oil change
Empty the fuel tank.
Unscrew the oil filler cap.
Place a suitable vessel to collect the oil in.
Drain the oil by tipping the engine so that the oil runs
out through the filler pipe. Ask where you can dispose
of surplus engine oil at your local petrol station.
Fill with new engine oil of a good quality. See
instructions in the section "Technical data".
Cutting equipment
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be
replaced.
Always ensure the cutter is well ground and balanced
correctly.
!
WARNING! The user must only carry out
the maintenance and service work
described in this Operator's Manual.
More extensive work must be carried out
by an authorized service workshop.
Switch off the engine before carrying out
any checks or maintenance. Prevent
unintentional starting by removing the
ignition cable from the spark plug.
The life span of the machine can be
reduced and the risk of accidents can
increase if machine maintenance is not
carried out correctly and if service and/or
repairs are not carried out professionally.
If you need further information please
contact your nearest service workshop.
Before starting
Weekly
maintenance
Monthly
maintenance
General inspection Spark plug Air filter
External cleaning Muffler* Fuel system
Oil level
Cutting equipment
Cutting cover*
Adjusting the clutch
wire
Engine brake handle
!
WARNING! Always wear heavy-duty
gloves when servicing and maintaining
the cutting equipment. The cutters are
very sharp and cuts can occur very
easily.
CAUTION! The blades should be balanced after
sharpening.
Damaged blades should be replaced when hitting
obstacles that result in a breakdown.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 140S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 140S in the language / languages: English, German, French, Italian, Swedish as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna LC 140S

Husqvarna LC 140S User Manual - All languages - 324 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info