518064

Husqvarna Huskystar 224 Manual

51
Zoom out
Zoom in
Previous page
1/56
Next page
49
Troubleshooting
Condition
The needle
thread breaks.
The bobbin
thread breaks.
The needle
breaks.
Skipped stitches
Seam puckering
Cause
1. The needle thread is not threaded
properly.
2. The needle thread tension is too tight.
3. The needle is bent or blunt.
4. The needle is incorrectly inserted.
5. The needle thread and the bobbin thread
are not set properly under (drawn to the
rear of ) the presser foot when sewing is
starting.
6. The fabric is not drawn to the rear when
sewing is fi nished.
7. The thread is too heavy or too fi ne for
the needle.
8. The thread is old and brittle.
1. The bobbin thread is not threaded
properly in the bobbin holder.
2. Lint has collected in the bobbin holder.
3. The bobbin is damaged and doesn´t turn
smoothly.
1. The needle is incorrectly inserted.
2. The needle is bent or blunt.
3. The needle clamp screw is loose.
4. The fabric is not drawn to the rear when
sewing is fi nished.
5. The needle is too fi ne for the fabric being
sewn.
1. The needle is incorrectly inserted.
2. The needle is bent or blunt.
3. The needle and/or threads are not
suitable for the work being sewn.
4. A blue tipped needle is not being used
for sewing stretch, very fi ne fabrics or
synthetics.
5. The needle thread is not threaded
properly.
6. The wrong needle is used.
1. The needle thread tension is not tight.
2. The needle thread is not threaded
properly.
3. The needle is too heavy for the fabric
being sewn.
4. The stitch length is too long for the fabric.
5. The presser foot pressure is not correctly
adjusted.
Reference
Refer to page 15
Refer to page 20
Refer to page 11
Refer to page 11
Refer to page 21
Refer to page 22
Refer to page 11
Refer to page 14
Refer to page 47
Change the bobbin.
Refer to page 11
Refer to page 11
Refer to page 11
Refer to page 22
Refer to page 11
Refer to page 11
Refer to page 11
Refer to page 11
Refer to page 11
Refer to page 15
Change the needle.
Refer to page 20
Refer to pages 14, 15
Refer to page 11
Make stitch denser.
Refer to page 8
… 51 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-huskystar-224

Reset search

  • How do I set my machine to zigzag
    My machine only makes small stitches even when I change the length Submitted on 5-3-2022 at 21:36

    Reply Report abuse

  • I can not replace a new needle. Difficult to find entrance Submitted on 19-2-2022 at 22:45

    Reply Report abuse

  • The machine started bunching all the cotton on the underside of the material and would not progress. In the manual it suggests that lint might have collected, it had, so I cleaned this out thoroughly. I read troubleshooting in the manual and it mentioned the position of the feed teeth and the lever to the back and below the free arm bed, I slid this across and the teeth dropped but would not rise when I slid it back to the "raise feed teeth" position. It had no effect so now cannot use the machine. Can one repair this, if so, how? Thank you. Submitted on 8-12-2021 at 13:25

    Reply Report abuse

  • the reverse is not working, am i missing a setting?
    Submitted on 20-4-2020 at 06:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskystar 224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskystar 224 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info