510458
17
Zoom out
Zoom in
Previous page
1/28
Next page
17
Stitch À nger lever setting
The stitch À nger lever should be set to “S” for all standard
overlock sewing. To sew rolled edge you need to retract the stitch
À nger by setting the stitch À nger lever to “R”. When moving the
stitch À nger, be sure to push the lever as far as it will go in each
direction.
Rolled edge sewing
The rolled edge stitch is appropriate for light weight fabrics such
as lawn, voile, organdy, crepe, etc. The rolled edge is achieved by
adjusting the thread tension to make the fabric edge roll under the
fabric while overlocking. Adjust the thread tension to change the
degree of rolling. To sew rolled edge you need to set the stitch
À nger lever to “R”. The minimum overlock stitch width that can
be obtained for rolled edging is approximately 1.5 mm since the
cutting width cannot be set below 3.5 mm.
A variant of the rolled edge stitch is the narrow edge. It can be
obtained by adjusting the thread tension according to the stitch
table on pages 23-26.
Tip: For a beautiful rolled edge, thread the upper looper
with a decorative thread and the needle and lower looper with
lightweight regular thread.
2-thread rolled edge / narrow edge
1. Attach the 2-thread overlock converter (see page 8).
2. Use the right needle thread and lower looper thread.
3. Move the stitch À nger lever to “R”.
4. Set the stitch length dial to “N-2” for a À ne seam.
5. Set the thread tension according to the stitch table on pages
23-26.
6. Make a thread chain and test sew on a sample of your fabric
before sewing on your garment. Hold the thread chain while
beginning to sew to keep it from curling into the seam.
3-thread rolled edge / narrow edge
1. Use the right needle thread and the upper and lower looper
threads.
2. Move the stitch À nger lever to “R”.
3. Set the stitch length dial to “N-2” for a À ne seam.
4. Set the thread tension according to the stitch table on pages
23-26.
5. Make a thread chain and test sew on a sample of your fabric
before sewing on your garment. Hold the thread chain while
beginning to sew to keep it from curling into the seam.
2-thread rolled edge 2-thread narrow edge
3-thread rolled edge 3-thread narrow edge
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna HUSKYLOCK s15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna HUSKYLOCK s15 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna HUSKYLOCK s15

Husqvarna HUSKYLOCK s15 User Manual - German - 28 pages

Husqvarna HUSKYLOCK s15 User Manual - Dutch - 28 pages

Husqvarna HUSKYLOCK s15 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info