Manual Husqvarna Huskylock 90 (page 30 of 36) (English, Spanish)

610254

Zoom out

Zoom in

1/36

Huskylock 9030

Replacing the cutters / Cambio de cuchillos

Turn the power switch to "OFF" before

replacing the cutter blades.

The lower cutter is made of a special

material and does not usually need to be

replaced. However, should it become

damaged, it can be replaced by your local

dealer.

When the upper cutter becomes dull,

replace it as follows:

1) Open the front cover and turn the

handwheel toward you until the

needles are in the lowest position.

2) Use the screwdriver (found in the

accessory box) and loosen the upper

cutter set screw and remove the cutter.

3) Place the new upper cutter, slightly

tighten the upper cutter set screw.

4) Adjust the position of the upper cutter

so the edge of the upper cutter

overlaps 0.5-1.0 mm from the edge of

lower cutter as shown below.

5) Tighten the upper cutter set screw

firmly and close the front cover.

Desconecte la máquina de la red.

El cuchillo superior puede estar gastado y

debe reemplazarse. El cuchillo inferior

esta hecho de material especial y

normalmente no necesita cambiarse. En

caso que esté dañado, su revendedor

pueda cambiarlo.

1) Abra la tapa frontal girando el volante

hasta que las agujas estén en su posión

baja.

2) Utlice el destornillador y afloje el

tornillo del cuchillo superior sacándolo.

3) Monte el nuevo cuchillo apetando el

tornillo de nuevo.

4) Asegúrese que el borde del cuchillo

superior solape el borde del cuchillo

inferior de 0,5 - 1 mm.

5) Cierre la tapa frontal

Lower cutter

Cuchillo inferior

Upper cutter

Cuchillo superior

Screwdriver

Destornillador

Solapado 0,5-1.0 mm

Overlaps 0.5-1.0 mm

Upper cutter set screw

Tornillo del cuchillo superior

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 90 in the language / languages: English, Spanish as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna Huskylock 90 Manual

Product: