610232

Husqvarna Huskylock 341 Manual

19
Zoom out
Zoom in
Previous page
1/44
Next page
ALIGNMENT
OF
AXED
CUTTER
It
may
be
necessary
to
realign
the
fixed
cutter
for
narrow/rolled
hems
to
accomplish
the
special
effect
you
desire.
1.
Loosen
screws(D)
and
align
fixed
cutter(E)
so
that
the
right
side
of
fixed
cutter(E)
lines
up
with
needle
plate
as
shown
in
Fig.
2.
2.
Make
sure
that
the
top
of
fixed
cutter(E)
is
aligned
with
needle
plate
surface
and
then
tighten
screws(D)
securely.
3.
Loosen
screw(G)
and
moving
cutter(H)
will
be
pulled
by
spring
until
it
touches
with
fixed
cutter(E).
Tighten
screw(G)
while
you
push
shaft
end(F)
to
right
slightly
by
fingers.
Make
sure
there
is
no
gap
between
two
cutters.
CHANGING
TO
STANDARD
NEEDLE
PLATE
AND
PRESSER
FOOT
1.
Remove
presser
foot
and
needle
plate.
2
Put
right
needle
back
into
needle
bar.
3.
Place
standard
needle
plate.
4.
Loosen
screw(G)
and
slide
moving
cutter(H)
right
away
from
fixed
cutter(E)
by
pushing
shaft
end(J),
and
then
tighten
screw(G)
tentatively.
.
5.
Loosen
screws(D)
and
move
fixed
cutter(E)
to
right
to
align
its
right
side
with
needle
plate
as
shown
in
Fig.
3.
6.
Tighten
screws(D)
securely
while
fixed
cutter(E)
is
held
in
parallel
with
needle
plate.
7.
Loosen
screw(G)
and
moving
cutter
will
be
pulled
by
spring.
8.
Tighten
screw(G)
while
you
push
shaft
end(F)
slightly
to
right
by
fingers.
Make
sure
there
is
no
gap
between
both
cutters.
9.
Place
standard
presser
foot.
Fig.
2
cutter
Fig.
3
17
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskylock 341 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 341 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info