610232
18
Zoom out
Zoom in
Previous page
1/44
Next page
ADJUSTING
OVERLOCK
STITCH
WIDTH
Stitch
width
can
be
adjusted
by
changing
needle
plate
and
presser
foot.
When
first
delivered
your
machine
will
be
fitted
with
the
standard
5.0
mm
needle
plate
and
presser
foot,
which
will
be
found
suitable
for
most
general
overlocking
requirements.
Your
machine
is
also
supplied
with
a
set
of
needle
plate
and
presser
foot
for
narrow
(about
2
mm)
and
rolled
hems.
These
will
be
found
in
and
your
accessory
box.
Needle
plate
and
presser
foot
CHANGING
TO
NEEDLE
PLATE
for
narrow/rolled
hems.
AND
PRESSER
FOOT
FOR
NARROW/ROLLED
HEMS
FIRST
DISCONNECT
MACHINE
FROM
POWER
SUPPLY
BY
REMOVING
PLUG
FROM
SOCKET-OUTLET.
During
the
changing
operation
be
careful
to
keep
fingers
away
from
both
cutters.
1.
Unthread
machine.
2.
Raise
needles
to
its
highest
point
by
turning
hand
wheel
towards
you
and
also
raise
presser
foot.
3.
Open
both
front
and
side
cover
plates.
4.
Loosen
thumb
screw(A)
and
remove
presser
foot
in
use.
(Fig.
1)
5.
Remove
right
needle
and
use
left
needle
only.
6.
Place
presser
foot
for
narrow/rolled
hems
and
secure
with
thumb
screw.
7.
Take
off
needle
plate
in
use
by
removing
screw(C)
and
lifting
plate
up
from
guide
pin(B).
(Fig.
1)
8.
Place
needle
plate
for
narrow/rolled
hems
into
position
and
secure
with
screw(C).
Standard
needle
plate
presser
foot.
Fig.
1
16
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskylock 341 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 341 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info