477472
25
Zoom out
Zoom in
Previous page
1/40
Next page
To adjust the high speed needle (H)
The engine is adjusted at the factory to operate at sea
level. At higher altitudes, in different weather or different
temperatures it can be necessary to adjust the high
speed needle.
Turn the high speed needle to make adjustments.
CAUTION: Do not turn the high speed
needle screw across the adjustment
limitation stop. This can cause damage
to the piston and the cylinder.
To adjust the start throttle speed
1. Apply idle speed.
2. Push the start throttle lock. Refer to
To start with a
throttle handle with a start throttle lock on page 17
.
3. If the start throttle speed is less than 4000 rpm, turn
the adjuster screw (A) until the cutting attachment
rotates. Turn the adjuster screw 1/2 turn more.
A
4. If the start throttle speed is too high, turn the adjuster
screw (A) counterclockwise until the cutting
attachment stops. Turn the adjuster screw 1/2 turn
more.
To adjust the idle speed
Your Husqvarna product is designed and made to
specifications that decrease harmful emissions.
Make sure that the air filter is clean and the air filter
cover is attached before you adjust the idle speed.
Adjust the idle speed with the idle adjustment screw
T which is identified with "T" mark.
WARNING: If the cutting attachment
does not stop when you adjust the idle
speed, turn to your nearest servicing
dealer. Do not use the product until it is
correctly adjusted or repaired.
The idle speed is correct when the engine operates
smoothly in all positions. The idle speed must be
below the speed when the cutting attachment starts
to turn.
1. Turn the idle adjustment screw clockwise until the
cutting attachment starts to turn.
2. Turn the idle adjustment screw counterclockwise
until the cutting attachment stops.
Note: See
Technical data on page 28
for the
recommended idle speed.
To sharpen the grass knife and grass
blade
WARNING: Stop the engine. Use protective
gloves.
To sharpen the grass knife or grass blade correctly,
refer to the instructions that come with the cutting
attachment.
Sharpen all edges equally to keep the balance.
Use a single-cut flat file.
WARNING: Always discard a blade that is
damaged. Do not try to make a bent or
twisted blade straight and use it again.
To sharpen the saw blade
WARNING: Stop the engine. Use protective
gloves.
To sharpen the blade correctly, refer to the
instructions that come with the blade.
1069 - 005 - 25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 535RX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 535RX in the language / languages: English as an attachment in your email.

The manual is 4,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 535RX

Husqvarna 535RX User Manual - German, Dutch, French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info