477472
24
Zoom out
Zoom in
Previous page
1/40
Next page
The grease in the bevel gear does not need to be
changed unless repairs are carried out.
To attach and remove the locknut
WARNING: Stop the engine, use protective
gloves and be careful around the sharp
edges of the cutting attachment.
A locknut is used to attach some types of cutting
attachments. The locknut has a left thread.
To attach, tighten the locknut in the opposite
direction to the direction of turning of the cutting
attachment.
To remove the locknut, loosen the locknut in the
same direction as the cutting attachment rotates.
To loosen and tighten the locknut, use a socket
wrench with a long shaft. The arrow in the picture
shows the area where you can operate the socket
wrench.
WARNING: When you loosen and
tighten the locknut, there is a risk of
injury from the blade. You must always
make sure that the blade guard prevents
injury to your hand when you do this.
Note: Make sure that you can not turn the locknut by
hand. Replace the nut if the nylon lining does not have a
resistance of a minimum of 1.5 Nm. The locknut must be
replaced after it has been put on approximately 10
times.
To examine the spark plug
CAUTION: Always use the recommended
spark plug type. Incorrect spark plug type
can cause damage to the product.
Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
Technical data
on page 28
.
Replace the spark plug if it is necessary.
To adjust the engine
Follow these instructions if the engine does not operate
correctly.
1. Attach an approved cutting attachment, see
Accessories on page 29
.
2. Start the engine.
3. Operate the product in usual conditions for 3
minutes.
4. Lift the cutting attachment in the air and apply full
throttle for 30 seconds. If a trimmer head is used,
make sure that the trimmer line is cut to correct
length by the guard knife.
Note: Do not cut grass or branches during this step.
5. Operate the product in usual conditions to make sure
that the engine operates correctly.
6. If the engine does not operate correctly, do step 4
and 5 again 3 times.
7. Let your Husqvarna dealer adjust/repair the product
if the engine does not operate correctly after you
have done all these steps.
To adjust the low speed needle (L)
Turn the low speed needle clockwise until stop.
Note: If the product has a bad acceleration capacity
or if the idle speed is not correct, turn the low speed
needle counterclockwise. Turn the low speed needle
until the acceleration capacity and idle speed is
correct.
24 1069 - 005 -
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 535RX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 535RX in the language / languages: English as an attachment in your email.

The manual is 4,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 535RX

Husqvarna 535RX User Manual - German, Dutch, French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info