734154
18
Zoom out
Zoom in
Previous page
1/460
Next page
product each day. Only do the maintenance work that is
found in this manual. Speak to an approved service
center about other maintenance work not found in this
manual.
Daily maintenance
Clean the external surfaces.
Make sure that the throttle trigger lockout and throttle
trigger work correctly.
Clean the chain brake and make sure that it
operates correctly.
Examine the chain catcher for damage. Replace the
chain catcher if it is damaged.
Turn the guide bar daily for more equal wear.
Make sure that the lubrication hole in the guide bar is
not clogged.
Remove saw dust and other unwanted material from
below the clutch cover.
Clean the guide bar groove.
(Fig. 58)
Make sure that the guide bar and saw chain get
sufficient oil.
Examine the saw chain for cracks and irregularly
worn rivets and links. If necessary, replace the saw
chain.
Examine the saw chain for the correct tension and
for burrs on the chain drive links. If necessary,
replace the saw chain.
Sharpen the saw chain. Refer to
To sharpen the saw
chain on page 19
.
Examine the drive sprocket for too much wear and
replace if necessary.
(Fig. 59)
Clean the air intake of the starter housing.
Make sure that the nuts and screws are tight.
Make sure that the controls operate correctly.
Weekly maintenance
Make sure that the cooling system works correctly.
Make sure that the starter, starter cord and return
spring work correctly.
Make sure that the vibration damping elements are
not damaged.
(Fig. 60)
File off any burrs from the edges of the guide bar.
Clean or replace the spark arrester mesh on the
muffler.
(Fig. 61)
Clean the external surfaces of the carburetor and its
adjacent areas.
Clean the air filter. Install a new air filter if it is
damaged or too dirty to be fully cleaned. Refer to
To
clean the air filter on page 19
for more information.
Monthly maintenance
Examine the brake band on the chain brake for
wear. Replace when the brake band thickness is
less than 0.6 mm (0.024 in) at the most worn point.
(Fig. 62)
Examine the clutch center, clutch drum and clutch
spring for wear.
Clean the spark plug. Make sure that the electrode
gap is correct.
(Fig. 63)
Clean the external surfaces of the carburetor and its
adjacent areas.
Examine the fuel filter and the fuel hose. Replace if
necessary.
Empty the fuel tank.
Empty the oil tank.
Examine all cables and connections.
Yearly maintenance
Examine the spark plug.
Clean the external surfaces of the carburetor and its
adjacent areas.
Clean the cooling system.
Examine the spark arrester mesh.
Examine the fuel filter.
Examine the fuel hose for damage.
Examine all cables and connections.
Intermittent maintenance
Have an approved service center repair or replace
the muffler after 50 hours of operation.
Do maintenance on the spark plug when:
the power level in the engine is low.
it is hard to start the engine.
the engine does not work correctly at idle speed.
Do a check of the saw chain lubrication each time
you refuel. See
To do a check of the saw chain
lubrication on page 20
.
To adjust the idle speed
Make sure that the air filter is clean and the air filter
cover is attached before you adjust the idle speed.
1. Turn the idle adjustment screw, which is identified
with a "T" mark, clockwise until the saw chain starts
to turn.
2. Turn the idle adjustment screw, which is identified
with a "T" mark, counterclockwise until the saw chain
stops.
3. The idle speed must be below the speed when the
saw chain starts to turn. The idle speed is correct
when the engine operates smoothly in all positions.
18
862 - 002 - 03.12.2018
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 135 Mark II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 135 Mark II in the language / languages: All languages as an attachment in your email.

The manual is 4,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info