734154
16
Zoom out
Zoom in
Previous page
1/460
Next page
To fill the fuel tank
1. Make sure that the fuel mixture is correct and that
the fuel mixture is in a fuel container with an antispill
valve.
2. If fuel is on the container, remove the unwanted fuel
and let the container dry.
3. Make sure that the area near the fuel tank cap is
clean.
4. Remove the fuel tank cap. (Fig. 44)
5. Shake the fuel container before you add the fuel
mixture to the fuel tank.
6. Put back the fuel tank cap.
To lubricate the saw chain
The product has an automatic lubrication system. Make
sure to only use the correct chain oil and obey the
instructions.
1. Use vegetable-based saw chain oil or a standard
chain oil.
2. Make sure that the area near the cap of the saw
chain oil tank is clean.
3. Remove the cap of the saw chain oil tank.
4. Fill the saw chain oil tank with the recommended
saw chain oil.
5. Put back the cap of the saw chain oil tank.
Before you start the engine
Examine the product for missing, damaged, loose or
worn parts.
Examine the nuts, screws and bolts.
Examine the air filter.
Examine the throttle trigger lockout and the throttle
control for correct operation.
Examine the stop switch for correct operation.
Examine the product for fuel leaks.
Examine the saw chain sharpness and tension.
To start a cold engine
1. Move the front hand guard forward to engage the
chain brake. (Fig. 45)
2. Pull the choke control out and up.
3. Push the air purge bulb 6 times. (Fig. 46)
4. Hold the body of the product on the ground with your
left hand.
5. Put your right foot through the rear handle.
6. Pull the starter rope handle slowly with your right
hand until you feel some resistance.
7. Pull the starter rope handle with force. (Fig. 47)
CAUTION:
Do not pull the starter rope
until it stops. Do not let go of the starter
rope when it is fully extended. Release
the starter rope slowly. If you do not
obey these instructions, it can cause
damage to the engine.
Note: Do not pull the throttle trigger when you start
the engine.
8. Continue to pull the starter rope handle until the
engine starts or tries to start (pull max 3 times).
9. If the engine starts or tries to start, push the choke
control down. (Fig. 48)
10. Continue to pull until the engine starts.
11. Hold the rear handle with your right hand and the
front handle with your left hand.
12. Immediately pull the front hand guard rearward in the
direction of the front handle to disengage the chain
brake. (Fig. 27)
Note: The chain will move.
13. Run 20-30 seconds at elevated idle speed.
14. Pull the throttle trigger lightly to set normal idle.
15. Run 20-30 seconds at normal idle.
16. Use the product.
To start a warm engine
1. Move the front hand guard forward to engage the
chain brake. (Fig. 45)
2. Pull the choke control out and up.
3. Push the air purge bulb 6 times. (Fig. 46)
4. Push the choke control down. (Fig. 48)
5. Hold the body of the product on the ground with your
left hand.
6. Put your right foot through the rear handle.
7. Pull the starter rope handle slowly with your right
hand until you feel some resistance.
8. Pull the starter rope handle with force. (Fig. 47)
CAUTION:
Do not pull the starter rope
until it stops. Do not let go of the starter
rope when it is fully extended. Release
the starter rope slowly. If you do not
obey these instructions, it can cause
damage to the engine.
Note: Do not pull the throttle trigger when you start
the engine.
9. Pull the starter rope handle until the engine starts.
10. Hold the rear handle with your right hand and the
front handle with your left hand.
11. Immediately pull the front hand guard rearward in the
direction of the front handle to disengage the chain
brake. (Fig. 27)
Note:
The chain will move.
16 862 - 002 - 03.12.2018
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 135 Mark II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 135 Mark II in the language / languages: All languages as an attachment in your email.

The manual is 4,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info