35206
65
Zoom out
Zoom in
Previous page
1/72
Next page
65
TROUBLESHOOTING GUIDE
Before calling for service, check the following items. If the problem still persists, contact the place
of purchase or your nearest authorized dealer.
Problem Cause Correction
Upper
thread
breaks
1.The machine is not threaded correctly. 1.Rethread the machine.
2.The thread tension is too tight. 2.Reduce the thread tension (lower number).
3.The thread is too thick for the needle. 3.Select a larger needle.
4.The needle is not inserted correctly.
4.Remove and reinsert the needle (À at side towards
the back).
5.The thread is wound around the spool holder pin. 5.Remove the spool and wind thread onto spool.
6.The needle is damaged. 6.Replace the needle.
Lower
thread
breaks
1.The bobbin case is not inserted correctly.
1.Remove and reinsert the bobbin case and pull on
the thread. The thread should pull easily.
2.The bobbin case is threaded wrong. 2.Check both bobbin and bobbin case.
3.The lower thread tension is too tight 3.Loosen lower thread tension.
Skipped
stitches
1.The needle is not inserted correctly.
1.Remove and reinsert needle (À at side towards the
back).
2.The needle is damaged. 2.Insert a new needle.
3.The wrong size needle has been used. 3.Choose a needle to suit the thread.
4.The foot is not attached correctly. 4.Check and attach correctly.
5.The machine is not threaded correctly. 5.Rethread the machine.
6.The presser foot pressure is not correct. 6.Increase the presser foot pressure.
Needle
breaks
1.The needle is damaged. 1.Insert a new needle.
2.The needle is not correctly inserted.
2.Insert the needle correctly (À at side towards the
back).
3.Wrong needle size for the fabric. 3.Choose a needle to suit the thread and fabric.
4.The wrong foot is attached. 4.Select the correct foot.
5.The needle clamp screw is loose. 5.Use the screwdriver to ¿ rmly tighten the screw.
6.The presser foot that is used is not appropriate for
the type of stitch that you wish to sew.
6.Attach the presser foot that is appropriate for the
type of stitch that you wish to sew.
7.The upper thread tension is too tight. 7.Loosen the upper thread tension.
Loose
stitches
1.The machine is not correctly threaded. 1.Check the threading.
2.The bobbin case is not correctly threaded. 2.Thread the bobbin case as illustrated.
3.Needle/fabric/thread combination is wrong. 3.The needle size must suit the fabric and thread.
4.Thread tension is wrong. 4.Correct the thread tension.
Seam
gather or
pucker
1.The needle is too thick for the fabric. 1.Select a ¿ ner needle.
2.The stitch length is adjusted wrong. 2.Shorten the stitch length.
3.The thread tension is too tight. 3.Loosen the thread tension.
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huskystar C10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huskystar C10 in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huskystar C10

Huskystar C10 User Manual - Dutch - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info