685866
6
Zoom out
Zoom in
Previous page
1/17
Next page
SEN C P 1 2 3 4 5 6 7 8
RST
24VAC
BAT
Battery Compartment
SEN C P 1 2 3 4 5 6 7 8
RST
24VAC
BAT
Valve Common Wire
Valve 1
Valve 2
Valve 3
Valve 4
Valve
Wires
Master Valve
Master Valve Wire
Lithium Battery
Battery
Holder
(--)
(+)
ENG
4
REPLACING THE BATTERY
A high-energy lithium battery is included with your
XC controller. The battery allows the user to remotely
program the controller without connecting AC power.
It is also used to keep the current time and day during
power outage conditions. To replace the battery:
1. Remove the screw from the battery holder.
2. Slide the battery holder down to
access the battery.
3. Remove and replace the new battery
into the battery holder and reinstall the
battery holder.
NOTE: This positive(+) side of the battery should face
the inside of the battery holder.
Battery type: CR2032 3V
CONNECTING A MASTER VALVE
NOTE: Complete this section only if you have a master
valve installed in your irrigation system. A master valve
is a "normally closed" valve installed at the supply point
of the main line that opens only when the controller
initiates a watering program.
1. At the Master Valve,
attach the common wire
to either solenoid wire
of the valve. Attach a
separate control wire to
the remaining solenoid
wire.
PSR Series
Pump Start Relay
4.5 Meters Minimum (15')
To Pump
RUN TIMES
CURRENT TIME/DAY
WATER DAYS
START TIMES
RUN
SEASONAL ADJUSTMENT
ALL
MANUAL-ALL STATIONS
SYSTEM OFF
1
MANUAL-ONE STATION
ACTIVE
SENSOR BYPASS
XC
CONNECTING A PUMP START RELAY
NOTE: Complete this section only if you have a pump
start relay installed. A pump start relay is a device that
uses a signal from the controller to actuate a separate
electrical circuit to energize a pump to provide water to
your system.
The controller should be mounted at least a 15 ft (4.5 m) away from
both the pump start relay and pump to minimize any potential electri-
cal interference.
1. Route a pair of wires from the pump relay into the controller.
2. Connect a common wire to the C (Common) terminal inside the
controller and connect the remaining wire from the pump start
relay to the P terminal.
Relay holding current draw must not exceed .30 amps. Do not connect
the controller directly to the pump or damage to the controller will result.
2. The common wire should be attached to the C terminal inside the
controller. The other wire coming from the master valve should be
attached to the P terminal inside the controller. Tighten each termi-
nal screw.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hunter XC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hunter XC in the language / languages: English as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hunter XC

Hunter XC User Manual - German - 17 pages

Hunter XC Quick start guide - Dutch - 1 pages

Hunter XC User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info