685907
74
Zoom out
Zoom in
Previous page
1/100
Next page
67
Select Solar Sync Check. The screen will show
Initializing for a few seconds as the controller
contacts the sensor.
If the check is successful, the screen will show
Sensor Check OK. Continue with the Operation and
Adjustment procedures if necessary.
If the check is not successful, the screen will show
“Sensor Check Failed”. Check sensor wiring and try
again. Remember, the wiring is DC polarized and the wire
from the green ET terminal in the ACC must be connected
to the green wire lead from the Solar-Sync sensor.
ASSIGN PROGRAMS
Select which of the ACC programs are to be adjusted
by Solar Sync. You may specify which of the 6
automatic programs will be adjusted. All programs set
to Solar Sync will be adjusted by the same percentage,
as determined by the Solar Sync.
Programs which are not adjusted will continue with
the same run times, and will not use the Solar Sync
adjustment. They may be adjusted manually, however.
This may be useful for specialized irrigation, or when
programs are used to control non-irrigation devices.
Turn the ACC dial to the Set Station Run Times dial
position.
Press the RIGHT arrow button to move through all the
run time fields, until the Seasonal Adjust selection is
highlighted.
Use the + and buttons to change the Seasonal Adjust
to S-SYNC”. This setting is between 100% and
101%, immediately after GLBL (global). When
Seasonal Adjust is set to S-SYNC, it will be adjusted
automatically according to the Solar Sync sensor.
Use the Programs button to move through each of the
programs, and select S-SYNC for any program that
you want Solar Sync to adjust.
Programs for which you do NOT want Solar-Sync
adjustment should be set to GLBL (they will stay at
the Seasonal Adjust level set manually for the rest of
the controller), or they may have individual Seasonal
Adjustments by Program as described in the Seasonal
Adjustment settings in basic controller operations.
If the S-SYNC selection does not appear for a
program (between 100% and 101%), the Solar
Sync option has not been properly enabled for
the controller. Review the Preparation and Setup
procedures to troubleshoot.
SENSOR SHUTDOWN PROGRAMMING
The Solar-Sync sensor can be used for sensor shutdown
of watering at the controller. The Solar Sync can shut off
irrigation automatically for Rain, or for freezing conditions.
In the ACC controller, sensors are programmed to shut
down by individual program.
SENSOR MAPPING
After the Solar-Sync sensor is set up and operational,
the built-in sensor inputs in the ACC controller can
be mapped” to use the Solar Sync sensor instead of
other external sensors.
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hunter ACC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hunter ACC in the language / languages: English as an attachment in your email.

The manual is 7,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hunter ACC

Hunter ACC User Manual - German - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info