685907
11
Zoom out
Zoom in
Previous page
1/100
Next page
4
meTal CabIneT, Wall mounT InsTallaTIon ...............................
Tools required:
Long drill bit and extension
Philips screwdriver or bit (for use with long
extension) – magnetic recommended
Wire strippers
31"
(80
cm
)
F
acepac
k D
oo
r
Location Requirement: A) a switch or circuit-breaker
shall be included in building installations; B) the switch
or breaker shall be in close proximity to the controller,
and within easy reach of the operator; C) the switch or
breaker shall be marked as the disconnecting device for
the controller.
Avoid direct exposure to sprinkler spray.
Do not install controller within 20" (7 m) of
high-voltage electrical sources, such as service
transformers, pump station motors, etc.
Shaded or partially shaded areas are preferable to
prolonged direct sunlight.
The ACC controller is relatively heavy, about 30 lbs/13.6 kg
in the metal wall mount configuration. Mounting includes
a positioning hanger to assist with installation.
Mounting hardware has been included, but it is the
installer’s responsibility to insure that adequate hardware
is used for the physical location.
ACC is approximately 15½" (40 cm) wide. Allow another
15½" (40 cm) to the left of the controller for the door to
open freely.
Before mounting, it is easier to remove the metal cabinet
door. Swing the door open, grasp the top securely, and
push up on the bottom of the door, near the lower hinge.
The hinges should disengage and the metal door can be
removed.
Positioning Hanger
Mounting Holes
Remove the facepack assembly from the controller.
1. Open the facepack door using the recess on the
right.
2. Disconnect the gray ribbon cable from the back of
the facepack. Pull gently on the ribbon cable; a slight
rocking motion may help disengage the connector.
3. Push up on the upper door hinge, and tilt the door
so that it disengages the hinge posts. Remove the
facepack and set aside in a safe location.
4. OPTIONAL: Locate the positioning hanger in the
upper center of the controller’s location on the wall,
leaving adequate clearance for the opened door to
the left.
5. Drill a pilot hole for the anchor and insert.
6. Install one #10 (5 mm) screw in this hanger position,
leaving approximately ¼" (6 mm) out of the anchor
to allow the controller to hang from this screw.
7. Hang the controller from the keyhole slot in the
positioning hanger.
8. Place a level on the top of the controller cabinet and
level.
9. Locate the 3 mounting holes in the cabinet. These
are visible from the front, with the facepack
removed, in deep recesses in the top two corners,
and another shallow recess in the bottom center.
10. Mark each of these 3 locations and install anchors.
11. Reposition controller on the hanger and use a long
screwdriver or drill extension (3"/75 mm) with
magnetic tip to install the remaining 3 screws, one
at each anchor position, and secure.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hunter ACC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hunter ACC in the language / languages: English as an attachment in your email.

The manual is 7,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hunter ACC

Hunter ACC User Manual - German - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info